SsangYong Rexton. Manual — part 10
DI0A-33
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
GENERAL INFORMATION
DI ENG SM - 2004.4
Y220_0A025
Y220_0A026
Y220_0A027
Y220_0A028
1. Before lifting up the vehicle with lift, correctly support the
lifting points and lift up.
2. When using a jack, park the vehicle on the level ground
and block front and rear wheels. Position the jack under
the frame and lift up the vehicle and then support with
chassis stand before service work.
3. Before service work, be sure to disconnect battery
negative (-) terminal to prevent damages by bad wire and
short.
4. If service from interior of the vehicle, use protection cover
to prevent damage and contamination of seat and floor.
5. Brake fluid and anti-freeze can damage painted surface
of body. So carefully handle them during service work.
During Service Work - Inspection
6. Use recommended and specified tools to increase
efficiency of service work.
7. Use only genuine spare parts.
DI0A-34
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
GENERAL INFORMATION
DI ENG SM - 2004.4
8. Never reuse cotter pin, gasket, O-ring, oil seal, lock
washer and self-locking nut. Replace them with new.
If reused, normal functions cannot be maintained.
9. Align the disassembled parts in clean according to
disassembling order and group for easy assembling.
10. According to installing positions, the bolts and nuts have
different hardness and design. So be careful not to mix
removed bolts and nuts each other and align them
according installing positions.
11. To inspect and assemble, clean the parts.
12. Securely clean the parts that related with oil not to be
affected by viscosity of oil.
13. Coat oil or grease on the driving and sliding surfaces
before installing parts.
14. Use sealer or gasket to prevent leakage if necessary.
15. Damaged or not, never reuse removed gasket. Replace
with new and cautious on installing directions.
16. Tighten every bolt and nut with specified torque.
17. When service work is completed, check finally whether
the work is performed properly or the problem is solved.
18. If work on the fuel line between priming pump and injector
(including return line), be sure to cover the removed parts
with cap and be careful not to expose the connecting
passage and removed parts to external foreign materials
or dust. (Refer to cleanness.)
19. If remove high pressure fuel supply pipe between HP pump
and fuel rail and high pressure fuel pipe between fuel rail
and each injector, be sure to replace them with new.
Y220_0A029
Y220_0A030
DI0A-35
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
GENERAL INFORMATION
DI ENG SM - 2004.4
Y220_0A031
Y220_0A032
5. Carefully install the wires not to be damaged during
installation/removal of parts due to interference.
6. Be careful not to throw or drop each sensor or relay.
7. Securely connect each connector until hear a “click”
sound.
Notice
Be careful not to modify or alter electrical system and
electrical device. Or there can be vehicle fire or serious
damage.
1. Be sure to disconnect battery negative (-) terminal during
every service work. Before disconnecting battery negative
(-) terminal, turn off ignition key.
2. Replace with specified capacity of fuse if there is bad,
blown or short circuited fuse. If use electrical wire or steel
wire other than fuse, there can be damages on the various
electrical systems. If replaced with over-capacity fuse,
there can be damages on the related electrical device
and fire.
3. Every wire on the vehicle should be fastened securely
not to be loosened with fixing clip.
4. If wires go through edges, protect them with tape or other
materials not to be damaged.
During Service Work for Electric
Devices
DI0A-36
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
GENERAL INFORMATION
DI ENG SM - 2004.4
2. Safety jack and safety stand
If lift up the vehicle with safety jack and stand, should be more
careful during works.
Warning
• Never be under the vehicle if supported with only jack.
If have to be under the vehicle, be sure to use safety
block.
• Use wheel block in front and rear of every wheel.
LIFTING POINTS
Lifting Positions
1. 4-post lift
As illustrated, position the vehicle on the 4-post lift securely and block the front and rear of each tire not to move during
working.
Notice
During lifting, be sure to check whether vehicle is empty.
• Board-on lift connection device installed in front of vehicle should be positioned in front of sill locating
under the front door.
• Install lift connecting device on the edge of front and rear of board-on lift.
Warning
• Be sure to use attachment during lifting to prevent the lift from contacting with body floor.
• While lifting the vehicle, widen the lift floor as far as possible to stabilize between vehicle front and rear. When
fixing the lift floor, be careful not to contact with brake tube and fuel lines.
Y220_0A033
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст