SsangYong Rexton. Manual — part 315
M162 ENGINE MECHANICAL 1B1-63
SSANGYONG Y200
YAD1B670
YAD1B590
YAD1B0E0
Removal & Installation Procedure
1. Turn the crankshaft to the direction of engine
rotation and position the no.1 cylinder piston at
TDC which the camshaft is positioned at OT.
2. Remove the cylinder head front cover. Refer to
“Cylinder Head Front Cover” in this section.
3. Paint the alignment marks (arrows) on the intake
and exhaust camshaft sprocket and the timing
chain.
4. Unscrew the bolt (3) from the armature (4) and
remove the armature.
Installation Notice
5. Unscrew the nut (6) and remove the ring and seal
cover (11).
Installation Notice
3 Bolt
4 Amarture
6 Nut (M20 x 1.5)
12 Seal Cover
13
Camshaft Sprocket
18
Control Piston
22
Intake Camshaft
Tightening Torque
35 N•m (26 lb-ft)
Tightening Torque
60 - 70 N•m
(44 - 52 lb-ft)
SSANGYONG Y200
1B1-64 M162 ENGINE MECHANICAL
YAD1B0F0
7. Remove the camshaft sprocket (13) and adjust
piston (14), and remove the flange shaft (16) from
the intake camshaft (22) after removing the bolt
(15).
Installation Notice
The sprocket bolt is designed to be used only
once, so always replace with new one.
8. Installation should follow the removal procedure
in the reverse order.
9. Adjust the camshaft timing.
Tightening Torque
1st step: 18 - 22 N•m
(13 - 16 lb-ft)
2nd step: 90° ± 5°
6. Unscrew the sprocket bolt from the exhaust
camshaft and remove the sprocket.
Installation Notice
The sprocket bolt is designed to be used only
once, so always replace with new one.
Tightening Torque
1st step: 18 - 22 N•m
(13 - 16 lb-ft)
2nd step: 90° ± 5°
M162 ENGINE MECHANICAL 1B1-65
SSANGYONG Y200
YAD1B0G0
YAD1B0H0
The sprocket bolts are designed to be used only once,
so always replace with new one.
Exhaust Camshaft Sprocket Bolt
Installation Notice
The sprocket bolts are designed to be used only once,
so always replace with new one.
C M7 x 13 Collar Bolt Torx-T30
e 6.8 mm
16 Flange Shaft
18 Control Piston
22 Intake Camshaft
E M7 x 13 Collar Bolt Torx-T30
e 6.8 mm
13a Camshaft Sprocket
22a Exhaust Camshaft
CAMSHAFT SPROCKET BOLT
Intake Flange Shaft Bolt
Installation Notice
Tightening Torque
1st step: 18 - 22 N•m
(13 - 16 lb-ft)
2nd step: 90° ± 5°
Tightening Torque
1st step: 18 - 22 N•m
(13 - 16 lb-ft)
2nd step: 90° ± 5°
SSANGYONG Y200
1B1-66 M162 ENGINE MECHANICAL
CAMSHAFT
Preceding Work : Removal of cylinder head cover
Removal of cylinder head front cover
Removal of coolant connection fitting
1 Chain Tensioner Assembly
. . . . . . . . . ... 72-88 N•m (53-65 lb-ft)
2 Exhaust Camshaft Sprocket
3 Upper Guide Rail
4 Cylinder Head Front Cover
5 Intake Camshaft Sprocket
6 Chain
7 Wrench
YAD1B0J0
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст