SsangYong Rexton. Manual — part 466
FRONT SUSPENSION 2C-13
SSANGYONG Y200
3. Remove the shock absorber and coil spring
assembly. Separate the lower yoke mounting bolt
and the yoke.
4. Remove the shock absorber yoke.
YAD2C170
YAD2C180
YAD2C190
5. Separate the shock absorber assembly with
pushing down the lower arm.
Installation Procedure
1. Install the coil spring(shock absorber) assembly
and the yoke to the body. And then install the
lower shock absorber into the yoke hole and insert
the upper shock absorber to bolt hole by
tightening the nut manually.
Installation Notice
YAD2C200
2. Tighten bolts of the shock absorber assembly and
yoke. Be careful to tightening direction of the bolt
as shown.(See the arrow).
Installation Notice
Tightening Torque
60 - 70 N•m
(44 - 52 lb-ft)
Tightening Torque
40 - 60 N•m
(30 - 44 lb-ft)
SSANGYONG Y200
2C-14 FRONT SUSPENSION
3. Fix the shock absorber yoke at the lower arm bolt
hole and insert to tighten the yoke mounting pin
to the hole.
Installation Notice
2. Remove mounting bolts and nuts of the upper arm/
frame bracket (both front and rear) and separate
the upper arm.
YAD2C210
YAD2C220
YAD2C230
UPPER/LOWER ARM ASSEMBLY
Removal Procedure
Notice: Perform the pre-work before the removal
procedure.
•
Remove the shock absorber.
•
Remove the steering knuckle by referring the
steering section.
1. Remove the mounting nut (slotted nut) and the
split pin (cotter pin) from the upper/lower arm ball
joint.
Notice: Separate the ball joint from the steering knuckle
using the special tool as shown.
Tightening Torque
150 - 180 N•m
YAD2C240
FRONT SUSPENSION 2C-15
SSANGYONG Y200
3. Remove mounting bolts and nuts of the lower arm
(both front and rear) and separate the lower arm.
3. Install the knuckle assembly to the shaft and insert
the ball joint of the upper/lower arm. And then
tighten the slotted nut and split pin.
Installation Notice
YAD2C250
YAD2C260
YAD2C270
YAD2C280
Installation Procedure
1. Install the lower arm to the frame bracket and
tighten the mounting bolt and nut as the specified
torque.
Notice :
•
Tighten the bolt on the direction from rear side
to front side of the vehicle.
•
Fix the bolt center with the bracket indication.
Installation Notice
2. Install the upper arm to the frame bracket.
Installation Notice
Tightening Torque
160 - 170 N•m
Tightening Torque
110 - 130 N•m
Slotted nut
Tightening
Torque
110 - 120 N•m
110 - 130 N•m
Upper side (1)
Lower side (2)
SSANGYONG Y200
2C-16 FRONT SUSPENSION
YAD2C310
4. Remove the coil spring components in specified
disassemble order.
Notice: Be careful to cause the spring elasticity
to any personal injury when it is separated the
special tool from the coil spring.
UNIT REPAIR
FRONT COIL SPRING
Removal Procedure
1. Remove the front coil spring assembly.
2. Fix the special tool to the coil spring assembly as
shown and compress the coil spring.
Notice: Install the special tool to the coil spring
tightly not to separate it during work and be careful
to spring end portion should look forward to the
person during compressing the coil spring.
YAD2C290
YAD2C300
3. Remove the shock absorber mounting nut and
remove the lock nut of the special tool in order to
separate the shock absorber.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст