Isuzu D-Max / Isuzu Rodeo (TFR/TFS). Manual — part 263
19
Program immobilizer ICU (Diesel Engine Model)
1. Select “Body” and “Immobilizer”.
2. See immobilizer status on the display of Tech 2.
3. Select engine type.
4. Enter the security code.
5. See ECM status.
6. Input the security code, then press the soft key of “Okay” or “Not Okay”.
Security Code
0000
Press ENTER Key to continue
Not
Okay
Okay
CAUTION
7. Enter VIN.
Vehicle Identification Number:
00000000000000000
Press ENTER Key to continue
Not
Okay
Okay
Enter VIN Input Screen
8. Enter Mechanical key number.
Mechanical Key Number:
- - - - - - -
Press ENTER Key to continue
Not
Okay
Okay
Enter Key No. Input Screen
20
9. Turn ON ignition.
Ignition Status Off 0V
Turn Ignition On!
Turn On Ignition
10. See the programming result.
Tech 2 displays the result of programming as the following.
Follow those instructions.
Selected Programming is not possible due to wrong System Status!
Immobilizer Not Programmed!
Immobilizer Already Programmed!
ECM Not Programmed!
ECM Already Programmed!
11. Transponder key must be reprogrammed, because all transponder information is erased
when ICU is programmed. See Transponder programming.
Program ECM
1. Procedure is the same as Program Immobilizer ICU procedure steps 1 through 5.
2. Turn On Ignition.
3. Select an Engine system.
4. See the display of programming result.
Program ECM / Immobilizer ICU
Caution:
1) Do not replace ICU and ECM at the same time.
2) Change ICU at first or ECM and other one change follows.
Follow Program Immobilizer ICU steps 1 through 6, procedure is the same as program
Immobilizer ICU procedure steps 1 through 6.
1. Input the security code.
2. Enter VIN.
3. Enter Key No.
4. Select an engine system.
See programming result display and follow instructions of the display.
5. Transponder key must be reprogrammed, because all transponder information on ICU is Erased when
ICU is programmed. See Transponder programming.
6. Follow program ECM steps 1 through 8.
21
Program Diesel Cutoff Solenoid
NOTE:
Perform this function only when the Immobilizer C/U is replaced.
1. Select "Body" and "Immobilizer".
2. Select engine type.
3. See Immobilizer status on the display of Tech 2.
4. Enter the security code.
5. See ECM or PCM status.
6. Select "F3: Program Diesel Cutoff Solenoid".
Programming
F0: Program Immobilizer Function
F1: Program Transponder-Keys
F2: Program Mechanical Key Number
F3: Program Diesel Cutoff Solenoid
7. Confirm the following screen shows up.
Program Diesel Cutoff Solenoid
See Checking Procedure Before
Programming!
(1) 2001 (TF) LUV
Electronic System: Immobilizer
Confirm
8. Confirm the following screen shows up.
Program Diesel Cutoff Solenoid
If Battery Voltage Is Low Disconnect
Fuse For Glow Plugs!
(1) 2001 (TF) LUV
Electronic System: Immobilizer
Confirm
22
9. Turn the ignition switch OFF/ON following the screen.
10. The following screen shows up.
Program Diesel Cutoff Solenoid
(1) 2001 (TF) LUV
Electronic System: Immobilizer
0
100
%
11. Follow the screen procedure.
12. Confirm that there is frequent rattling every 10 seconds.
Program Diesel Cutoff Solenoid
Frequent Rattling Every 10 Seconds?
(1) 2001 (TF) LUV
Electronic System: Immobilizer
NO
YES
13. Confirm the following screen shows up.
Program Diesel Cutoff Solenoid
Reconnect Fuse Glow Plugs!
(1) 2001 (TF) LUV
Electronic System: Immobilizer
Confirm
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст