Isuzu D-Max / Isuzu Rodeo (TFR/TFS). Manual — part 275
B8016 VEHICLE SPEED SIGNAL Hi (Gasoline Engine)
FREQUENCY SIGNAL Hi (Diesel Engine)
B8017 NO ENGINE REQUEST RECEIVED (Gasoline Engine)
Disconnect both
connectors and check
voltage on ICU side.
voltage
Ǩ 2.5v
Wiring repair
Yes
Clear DTC
No
Check path ICU
pin 3 and ECM pin B-8(V6)
J2-B4(L4) for continuity
Replace ECM, because ECM internal circuit fails.
OK
Wiring repair
NG
B8023 ANTENNA COIL OPEN
Antenna coil open
B8024 WRONG TRANSPONDER RESPONSE
Wrong Transponder code
Check path between
ICU pin 6 and pin 13
for continuity
Replace steering lock Assy
NG
Clear DTC
OK
OK
Check path between
ICU pin 6 and connector A pin
for continuity
Check path between
ICU pin 13 and connector A pin
for continuity
ICU
A connector 2 pin
6
13
Antenna coil
NG
Correction
NG
Correction
NG
NG
Need following repair
1. Key replacement
2. Rewrite transponder
3. Replace door key cylinder
Reregistration
ICU replacement
NG
Rewrite transponder
Diagnostic procedure
(4JA1-TC 2.5L/4JH1-TC 3.0L)
System guidance
Note:
Immobilizer may detect a history DTC by the timing of ON-OFF of a ignition switch.
Don't remove the ECM and ICU recklessly.
l Engine dose not run when any Diagnostic Trouble Code (DTC) is flagged, starting from 02MY
TFR/S.
l Once the cause of DTC is repaired or gone, engine can be operated normally, and present
DTC becomes history code.
l History code is canceled by no repeat failure on 25 consequence ignition key on afterward.
l History code cannot be canceled by battery connector disconnected, starting from 01MY.
Diagnostic Trouble Code (DTC) list
No
Code
(BCD)
Detecting Condition
1
B8001
Replace Electronic Control Unit(ECU)
This error code appears if a RAM /ROM Error was detected or the EEPROM
Is defect.
2
B8002
Immobiliser Not Programmed
3
B8003
Transponder Key Problem
Reading of Transponder information failed with ignition on transponder has
a fault.
Hardware fault in reading circuit.
4
B8004
Immobiliser Coil Circuit
5
B8005
Communication Line W Voltage Low
6
B8006
Communication Line W Voltage High
7
B8007
No Engine Request Received (Check Engine Lamp disconnected?)
8
B8008
Wrong Transponder Key
9
B8009
No Transponder Key Programmed
10
B8010
Unknown Transponder Key
Diagnostic procedure
No DTC indicates
Engine does not start to run even though all engine and electrical system are OK, and no DTC
appears.
1.
12V power is not supplied to ICU.
2.
Engine does not start after steering assembly is repaired.
Check if connector for Antenna coil circuit at steering shaft is correct, or missing connection.
If not correct, replace the steering assy with corrector.
3.
If engine does not start after ICU replacement, check part number (02MY).
Proper parts Numbers are following.
Electrical Die Engine
897234-671X
Suffix number
Check engine light
Is blinking at 2Hz.
ECM or electrical
unit wiring check
No
Yes
Yes
Starter is not rotated
By correct key at all.
Check DTC with Tech-2
12V power is not
supplied to ICU
Repair 12V circuit
ICU power supply turns off when both +B line
and ignition switch line turn off.
ICU
B-4 Pin
B-3 Pin
+B
Ignition SW
Check both wiring systems for continuity.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст