Isuzu D-Max / Isuzu Rodeo (TFR/TFS). Manual — part 969
4C1-46 FRONT WHEEL DRIVE
Important Operations
1. Wheel Pin
(1) Place hub on a wood workbench or a block of wood,
approx. 6” by 6” to protect the wheel stud ends and threads.
(2) Install wheel stud using a hammer.
Be sure wheel stud is started squarely and seats
completely.
(3) Align index marks and install hub to disc.
2. Bolt
Torque
N
⋅
m (kgf
⋅
m/lb
⋅
ft)
103
±
5 (10.5
±
1/75.9
±
7.2)
3. Inner Bearing and Outer Race
4. Oil Seal
▲
Outer Bearing Outer Race
(1) Install the bearing outer race by driving into the hub.
Installer (Outer) : 5-8822-0053-0 (J-29016)
Installer (Inner) : 5-8822-0054-0 (J-29015)
Drive handle
: 5-8840-0007-0 (J-8092)
(2) Install the outer and inner bearing into the hub with fingers.
FRONT WHEEL DRIVE 4C1-47
(3) Install oil seal using special tools.
Installer : 5-8522-0051-0
(J-33161)
Grip
: 5-8840-0007-0
(J-8092)
5. Hub and Disc Assembly
11. Hub Cap
Apply grease in the hub and hub cap.
Description
Amount g(oz)
Hub
50 (1.76)
Hub cap
20 (0.70)
Outer bearing
6.5 (0.23)
Inner bearing
12 (0.42)
8. Hub nut
Adjustment of front wheel hub bearing preload
1. Tighten spindle nut to 3.0 kg
⋅
m (21.7 lb.ft/29.4 N
⋅
m) torque.
2. Turn the hub 2-3 turns and loosen the nut just enough so
that it can be turned with the fingers.
3. Turn the nut all the way in with the fingers and check to be
sure the hub has no free play.
4. Measure the bearing preload by pulling one of the wheel hub
studs with a spring scale.
5. Tighten the spindle nut until specified bearing preload Is
obtained.
After reassembling, install the disc brake caliper assembly.
Bearing Preload
kg(lb)
New bearing and New oil seal
0.8 - 1.0(1.8 - 2.2)
Reuse bearing and New oil seal
0.8 - 1.0 (1.8 - 2.2)
13.Bolt
Torque
N
⋅
m (kgf
⋅
m/lb
⋅
ft)
155
±
15.7 (15.8
±
1.6/114.3
±
11.6)
4C1-48 FRONT WHEEL DRIVE
FRONT HUB AND DISC (4
×
4 model)
DISASSEMBLY
Refer to SECTION 3E “WHEEL AND TIRE” for wheel removal procedure
Disassembly Steps
1. Bolt
2. Hub cap
3. Snap ring and shim
4. Flange
5. Lock washer
▲
6. Hub nut
▲
7. Hub and disc assembly
8. Outer bearing
9. Oil seal
10. Inner bearing
FRONT WHEEL DRIVE 4C1-49
Important Operations
6. Hub nut
Wrench : 5-8840-2117-0
(J-36827)
Refer to Section 5 “Brake” for disc brake
caliper removal procedure.
7. Hub and disc assembly
Before disassembly, remove the disc brake caliper assembly
and hang it on the frame with wires.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст