Isuzu D-Max / Isuzu Rodeo (TFR/TFS). Manual — part 1975
4C2-20 FRONT DRIVING AXLE
Shift Drum
Function D
Function C
A
B
C
Dimensional Check
Measure illustrated sizes A, B, and C.
Limit
mm (in)
A
64.1 (2.52)
B
6.7 (0.26)
C
0.7 (0.03)
REASSEMBLY
15.Oil Seal
Install the new oil seal which has been immersed in
differential gear oil, by using an oil seal installer.
Installer : 5-8840-2407-0 (J-41693)
Grip
: 5-8840-0007-0 (J-8092)
14.Needle Bearing
Force a new needle bearing into inner shaft by using a
special tool.
Installer : 5-8840-2408-0 (J-41694)
Grip
: 5-8840-0007-0 (J-8092)
FRONT DRIVING AXLE 4C2-21
13.Inner Shaft Bearing
• Place a new snap ring in inner shaft.
• Force a new inner shaft bearing into the inner shaft.
Installer : 5-8840-2197-0 (J-37452)
12.Snap Ring
NOTE:
Be careful not to damage the inner shaft.
11.Inner Shaft
• Clean the housing contact surface of the front axle case.
• Insert inner shaft assembly into the front axle case.
NOTE:
Be careful not to damage oil seal.
10.Snap Ring
Install snap ring in the groove of front axle case.
NOTE:
Be sure to install the snap ring properly.
9. Clutch Gear
Apply differential gear oil to clutch oil.
8. Sleeve
Apply differential gear oil to sleeve.
;;;
;;;
7. Housing
• Clean contact surface with the front axle and actuator
mounting surface.
• Apply liquid gasket to the contact surface on the front axle
case and install in the housing.
6. Bolt
Tighten bolts to specified tightening torque.
Housing Bolt Torque
N
⋅m (kg⋅m/lb⋅ft)
116 (11.8/85)
4C2-22 FRONT DRIVING AXLE
;
;
5. Actuator
• Clean the actuator contact surface with the housing.
• Apply liquid gasket to the contact surface on the actuator
side.
• Align shift arm with the groove of sleeve and install the
actuator.
4. Bolt
Tighten bolts to specified torque.
Actuator Bolt Torque
N
⋅m (kg⋅m/lb⋅in)
13 (1.3/113)
3. Front Axle Drive shaft (LH side)
2. Bolt
• Install front axle drive shaft and mounting bracket.
• Tighten fitting bolts to specified tightening torque.
Bolt Torque
N
⋅m (kg⋅m/lb⋅ft)
116 (11.8/85)
1. Filler Plug
• Pour specified amount of differential gear oil.
Front Differential Oil Capacity
lit (Impq+/USqt)
1.5 (1.32/1.59)
Actuator Housing Oil Capacity
lit (Impq+/USqt)
0.12 (0.11/0.13)
• Install filler plug through packing and tighten to specified
torque.
Filler Plug Torque
N
⋅m (kg⋅m/lb⋅ft)
7.8 (8.0/58)
FRONT DRIVING AXLE 4C2-23
FRONT HUB AND DISC (4WD Model Normal Hub)
Disassembly Steps
1. Bolt
2. Hub cap
3. Snap ring and shim
4. Hub flange
5. Lock washer and lock screw
6. Hub nut
7. Hub and disc assembly
8. Outer bearing outer race
9. Oil seal
10.Inner bearing outer race
11.Bolt
12.Wheel pin
Reassembly Steps
12.Wheel pin
11.Bolt
10.Inner bearing outer race
9. Oil seal
8. Outer bearing outer race
7. Hub nad disc assembly
6. Hub nut
5. Lock washer and lock screw
4. Hub flange
3. Snap ring and shim
2. Hub cap
1. Bolt
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст