Isuzu Rodeo UE. Manual — part 431
6E2–479
RODEO 6VD1 3.2L ENGINE DRIVEABILITY AND EMISSIONS
2. Install the coil module and spark plug boot over the
spark plug.
014RW108
3. Secure the coil module to the rocker cover with two
screws.
014RW091
4. Connect the electrical connector at the coil module.
5. Connect the negative battery cable.
Catalytic Converter
Removal and Installation Procedure
Refer to
Engine Exhaust in Engine.
Air Conditioning Relay
Removal Procedure
1. Remove the fuse and relay box cover from under the
hood.
2. Consult the diagram on the cover to determine which
is the correct relay.
3. Pull the relay straight up and out of the fuse and relay
box.
014RW090
Installation Procedure
1. Insert the relay into the correct place in the fuse and
relay box with the catch slot facing forward.
2. Press down until the catch engages.
f
An audible “click” will be heard.
3. Install the fuse and relay box cover.
EVAP Canister Hoses
Service Information
To view the routing of the EVAP canister hoses, refer to
Vehicle Emission Control Information in Diagnosis. Use
6148M or equivalent when you replace the EVAP canister
hoses.
6E2–480
RODEO 6VD1 3.2L ENGINE DRIVEABILITY AND EMISSIONS
EVAP Canister
Removal Procedure
1. Disconnect the negative battery cable.
2. Disconnect the two hoses from the EVAP canister.
014RW117
3. Disconnect the fuel vapor connector and the purge
hose from the EVAP canister vent solenoid.
014RW130
4. Remove the two retaining bolts the EVAP canister to
the mounting bracket on the cross member.
014RW131
5. Remove the retaining bolt on the mounting bracket
the slide the canister out of mounting bracket.
014RW129
Inspection Procedure
1. Inspect the hoses for cracks and leaks.
2. Inspect the canister for a damaged case.
6E2–481
RODEO 6VD1 3.2L ENGINE DRIVEABILITY AND EMISSIONS
Installation Procedure
1. Slide the canister into mounting bracket the install the
mounting bracket bolt.
014RW129
2. Install the retaining bolts the EVAP canister to the
mounting bracket on the cross member.
014RW131
3. Connect the fuel vapor connector to the EVAP
canister vent solenoid.
4. Connect the two hoses to the EVAP canister.
014RW130
5. Disconnect the negative battery cable.
EVAP Canister Vent Solenoid
Removal Procedure
1. Disconnect the negative battery cable.
2. Disconnect the connector and hose.
014RW132
6E2–482
RODEO 6VD1 3.2L ENGINE DRIVEABILITY AND EMISSIONS
3. Slide the out of EVAP canister vent solenoid from
mounting bracket.
014RW135
Inspection Procedure
1. Check for cracks or leaks.
2. Energize the solenoid and try to blow through it. The
solenoid should not allow passage of air when
energized. (J 35616 Connector Test Kit can be used
to easily attach jumper wires from the battery to the
solenoid).
Installation Procedure
1. Slide the into EVAP canister vent solenoid from
mounting bracket.
014RW135
2. Connect the connector and hose.
014RW132
3. Connect the negative battery cable.
Fuel Tank Pressure Sensor
Removal Procedure
1. Remove the fuel pump assembly. Refer to
Fuel Tank
In Fuel Pump.
2. Carefully pry the fuel tank pressure sensor out of the
top of the fuel pump assembly.
014RW133
Inspection Procedure
1. Inspect the vapor pressure sensor for cracks in the
housing and corrosion on the electrical terminals.
2. Inspect the rubber grommet for tears and signs of rot.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст