Isuzu Rodeo UE. Manual — part 362

6E2–203

RODEO 6VD1 3.2L ENGINE DRIVEABILITY AND EMISSIONS

f

DTC P0155 can be cleared by using the Tech 2 “Clear
info” function or by disconnecting the PCM battery
feed.

Diagnostic Aids

Check for the following conditions:

f

Poor connection at PCM – Inspect harness connectors
for backed-out terminals, improper mating, broken
locks, improperly formed or damaged terminals, and
poor terminal-to-wire connection.

f

Damaged harness – Inspect the wiring harness for
damage. If the harness appears to be OK, observe the
display on the Tech 2 while moving connectors and
wiring harnesses related to the sensor. A change in the
display will indicate the location of the fault.

Reviewing the Failure Records vehicle mileage since the
diagnostic test last failed may help determine how often
the condition that caused the DTC to be set occurs. This
may assist in diagnosing the condition.

Test Description

Number(s) below refer to the step number(s) on the
Diagnostic Chart.

2. The HO2S should be allowed to cool before

performing this test. If the HO2S heater is
functioning, the signal voltage will gradually increase
or decrease as the sensor element warms. If the
heater is not functioning, the HO2S signal will
remain near the 450 mV bias voltage.

4. Ensures that the ignition feed circuit to the HO2S is

not open or shorted. The test light should be
connected to a good chassis ground, in case the
HO2S low or HO2S heater ground circuit is faulty.

5. Checks the HO2S heater ground circuit.

6. Checks for an open or shorted HO2S heater

element.

10.An open HO2S signal or low circuit can cause the

HO2S heater to appear faulty. Check these circuits
before replacing the sensor.

DTC P0155 –HO2S Heater Circuit Bank 2 Sensor 1

Step

Action

Value(s)

Yes

No

1

Was the “On-Board Diagnostic (OBD) System Check”
performed?

—

Go to

Step 2

Go to

OBD

System

Check

2

NOTE: If the engine has just been operating, allow the
engine to cool for at least 15 minutes before
proceeding.

1. Remove the fuel pump relay.
2. Connect a fused jumper at the fuel pump relay

socket, between the battery positive at the relay and
the relay wire that leads to the fuel pump and O2S
fuses.

3. Ignition “OFF.”
4. Install a Tech 2.
5. Ignition “ON,” engine “OFF.”
6. Monitor the Bank 1 HO2S 1 voltage for several

minutes.

Did the HO2S voltage go from bias voltage to above or
below the specified value?

Above 650

mV or below

250 mV

Refer to

Diagnostic

Aids

Go to

Step 3

3

Inspect the fuse for the Bank 2 HO2S 1 ignition feed.

Is the fuse open?

—

Go to

Step 15

Go to

Step 4

4

1. Ignition “OFF.”
2. Raise the vehicle.
3. Disconnect the Bank 2 HO2S 1 electrical connector.
4. Using a test light connected to a known good ground

(do not use Bank 2 HO2S 1 heater ground or Bank 2
HO2S 1 low), probe the ignition feed circuit at the
Bank 2 HO2S 1 electrical connector (PCM harness
side).

Does the test light illuminate?

—

Go to

Step 5

Go to

Step 7

6E2–204

RODEO 6VD1 3.2L ENGINE DRIVEABILITY AND EMISSIONS

DTC P0155 –HO2S Heater Circuit Bank 2 Sensor 1

(Cont'd)

Step

No

Yes

Value(s)

Action

5

Connect the test light between Bank 2 HO2S 1 ignition
feed and Bank 2 HO2S 1 heater ground.

Does the test light illuminate?

—

Go to

Step 6

Go to

Step 8

6

1. Allow the HO2S to cool for at least 15 minutes.
2. Using a DVM, measure resistance between the

Bank 2 HO2S 1 ignition feed and the Bank 2 HO2S 1
heater ground at the Bank 2 HO2S 1 pigtail.

Is the HO2S resistance within the specified values?

3-6 ohms

Go to

Step 9

Go to

Step 10

7

Repair the open Bank 2 HO2S 1 ignition feed circuit to
Bank 2 HO2S 1.

Is the action complete?

—

Verify repair

—

8

Repair the open Bank 2 HO2S 1 heater ground circuit.

Is the action complete?

—

Verify repair

—

9

1. Check for a poor connection at the Bank 2 HO2S 1

harness terminals.

2. If a poor connection is found, replace terminals.

Was a poor connection found?

—

Verify repair

Go to

Step 10

10

Check for a poor Bank 2 HO2S 1 signal or low circuit
terminal connection at the Bank 2 HO2S 1 harness
connector and replace terminal(s) if necessary.

Did any terminals require replacement?

—

Verify repair

Go to

Step 11

11

1. Ignition “OFF.”
2. Disconnect the PCM and check the continuity of the

Bank 2 HO2S 1 signal circuit and the Bank 2 HO2S
1 low circuit.

3. If the Bank 2 HO2S 1 signal circuit or HO2S low

circuit measures over 5 ohms, repair open or poor
connection as necessary.

Was a problem found?

—

Verify repair

Go to

Step 12

12

Check for a poor Bank 2 HO2S 1 low circuit terminal
connection at the PCM and replace the terminal if
necessary.

Did the terminal require replacement?

—

Verify repair

Go to

Step 13

13

Check for a poor Bank 2 HO2S 1 signal circuit terminal
connection at the PCM and replace the terminal if
necessary.

Did the terminal require replacement?

—

Verify repair

Go to

Step 14

14

Replace Bank 2 HO2S 1.

Is the action complete?

—

Verify repair

—

15

Locate and repair short to ground in Bank 2 HO2S 1
ignition feed circuit and replace the faulty fuse.

Is the action complete?

—

Verify repair

—

6E2–205

RODEO 6VD1 3.2L ENGINE DRIVEABILITY AND EMISSIONS

Diagnostic Trouble Code (DTC) P0157 HO2S Circuit Low Voltage Bank 2

Sensor 2

D06RW065

Circuit Description

To control emissions of hydrocarbons (HC), carbon
monoxide (CO), and oxides of nitrogen (NOx), a
three-way catalytic converter is used. The catalyst within
the converter promotes a chemical reaction which
oxidizes the HC and CO present in the exhaust gas,
converting them into harmless water vapor and carbon
dioxide. The catalyst also reduces NOx, converting it to
nitrogen. The powertrain control module (PCM) has the
ability to monitor this process using the Bank 2 HO2S 1
and the Bank 2 HO2S 2 heated oxygen sensors. The
Bank 2 HO2S 1 sensor produces an output signal which
indicates the amount of oxygen present in the exhaust
gas entering the three-way catalytic converter. The Bank
2 HO2S 2 sensor produces an output signal which
indicates the oxygen storage capacity of the catalyst; this
in turn indicates the catalyst’s ability to convert exhaust
gases efficiently. If the catalyst is operating efficiently, the
Bank 2 HO2S 1 signal will be far more active than that
produced by the Bank 2 HO2S 2 sensor. If the Bank 2
HO2S 2 signal voltage remains excessively low for an
extended period of time, DTC P0157 will be set.

Conditions for Setting the DTC

f

No related DTCs.

f

The engine is operating in “closed loop.”

f

Engine coolant temperature is above 60

°

C (140

°

F).

f

“Closed loop” commanded air/fuel ratio is between
14.5 and 14.8

f

Throttle angle is between 3% and 19%.

f

Bank 2 HO2S 2 signal voltage remains below 22 mV
during normal “closed loop” operation for a total of 106
seconds over a 125-second period of time.

OR

f

Bank 2 HO2S 2 signal voltage remains below 400 mV
during “power enrichment” mode fuel control operation
for up to 5 seconds.

Action Taken When the DTC Sets

f

The PCM will illuminate the malfunction indicator lamp
(MIL) the first time the fault is detected.

f

The PCM will store conditions which were present
when the DTC was set as Freeze Frame and in the
Failure Records data.

Conditions for Clearing the MIL/DTC

f

The PCM will turn the MIL “OFF” on the third
consecutive trip cycle during which the diagnostic has
been run and the fault condition is no longer present.

f

A history DTC P0157 will clear after 40 consecutive
warm-up cycles have occurred without a fault.

f

DTC P0157 can be cleared by using the Tech 2 “Clear
Info” function or by disconnecting the PCM battery
feed.

6E2–206

RODEO 6VD1 3.2L ENGINE DRIVEABILITY AND EMISSIONS

Diagnostic Aids

Check for the following conditions:

f

Heated oxygen sensor wiring – The sensor pigtail may
be mispositioned and contacting the exhaust system.

f

Poor PCM to engine grounds.

f

Fuel pressure – A condition which causes a lean
exhaust can cause DTC P0157 to set. The system will
go lean if pressure is too low. The PCM can
compensate for some decrease. However, if fuel
pressure is too low, a DTC P0157 may be set. Refer
to

Fuel System Diagnosis.

f

Lean injector(s) – Perform “Injector Balance Test.”

f

Vacuum leaks – Check for disconnected or damaged
vacuum hoses and for vacuum leaks at the intake
manifold, throttle body, EGR system, and PCV system.

f

Exhaust leaks – An exhaust leak may cause outside air
to be pulled into the exhaust gas stream past the
HO2S, causing the DTC P0157 to set. Check for
exhaust leaks near the Bank 1 HO2S 2 sensor.

f

MAF sensor – The system can go lean if the MAF
sensor signal indicates an engine airflow
measurement that is not correct. Disconnect the MAF
sensor to see if the lean condition is corrected. If so,
replace the MAF sensor.

f

Fuel contamination – Water, even in small amounts,
can be delivered to the fuel injectors. The water can
cause a lean exhaust to be indicated. Excessive
alcohol in the fuel can also cause this condition. Refer
to

Fuel System Diagnosis for the procedure to check

for fuel contamination.

f

If none of above conditions are present, replace the
affected HO2S 2.

Test Description

Number(s) below refer to the step number(s) on the
Diagnostic Chart.
3. DTC P0157 failing during operation may indicate a

condition described in the “Diagnostic Aids” above.
If the DTC P0157 test passes while the Failure
Records conditions are being duplicated, an
intermittent condition is indicated.

Reviewing the Failire Records vehicle mileage since the
diagnostic test last failed may help determine how often
the condition that caused the DTC to be set occurs. This
may assist in diagnosing the condition.

DTC P0157 – HO2S Circuit Low Voltage Bank 2 Sensor 2

Step

Action

Value(s)

Yes

No

1

Was the “On-Board Diagnostic (OBD) System Check”
performed?

—

Go to

Step 2

Go to

OBD

System

Check

2

1. Install the Tech 2.
2. Run the engine at operating temperature.
3. Operate the vehicle within the parameters specified

under “Conditions for Setting the DTC” criteria
included in Diagnostic Support.

4. Using a Tech 2, monitor Bank 2 HO2S 2 voltage.

Does the Bank 2 HO2S 2 voltage remain below the
specified value?

22 mV

Go to

Step 4

Go to

Step 3

3

1. Ignition “ON,” engine “OFF.”
2. Review and record Tech 2 Failure Records data and

note parameters.

3. Operate the vehicle within Failure Records

conditions as noted.

4. Using a Tech 2, monitor “DTC” info for DTC P0157

until the DTC P0157 test runs.

5. Note the test result.

Does the Tech 2 indicate DTC P0157 failed this
ignition?

—

Go to

Step 4

Refer to

Diagnostic

Aids

4

1. Turn the ignition “OFF.”
2. Disconnect the PCM.
3. Check the Bank 2 HO2S 2 high and low signal

circuits for a short to ground or a short to the heater
ground circuit.

Were Bank 2 HO2S 2 signal circuits shorted?

—

Go to

Step 5

Go to

Step 6

5

Repair the Bank 1 HO2S 2 signal circuit.

Is the action complete?

—

Verify repair

—