Isuzu KB P190. Manual — part 293

6E-138 Engine Control System (4JH1)

Step Action

Value(s)

Yes

No

16 1. Reconnect all previously disconnected fuse,

relay or harness connector(s).

2. Clear the DTCs with the scan tool.
3. Turn OFF the ignition for 30 seconds.
4. Start the engine and warm up (allow engine

coolant temperature to reach at least 65

°C

[149

°F]).

5. Monitor the DTC Information with the scan tool.
Did the DTC fail this ignition?



Go to Step 2

Go to Step 17

17

Observe the DTC Information with the scan tool.
Are there any DTCs that you have not diagnosed?



Go to Diagnostic

Trouble Code (DTC)

List System

OK

Engine Control System (4JH1) 6E-139

DTC P0380 (Symptom Code 8) (Flash Code 66)

Circuit Description
The engine control module (ECM) controls the glow
relay which supplies power to the glow plugs based on
engine coolant temperature. In the after glow phase, the
glow indicator light is not illuminated but glow plugs
remain active for a certain period. If the ECM detects a
short to battery or ignition voltage on the glow relay
control circuit, this DTC will set.
Condition for Running the DTC

• The ignition switch is ON.

Condition for Setting the DTC

• The ECM detects that the high voltage condition

on the glow relay control circuit for longer than 1
second when the relay is commanded ON.

Action Taken When the DTC Sets

• The ECM illuminates the malfunction indicator

lamp (MIL) when the diagnostic runs and fails.

Condition for Clearing the MIL/DTC

• The ECM turns OFF the MIL when the diagnostic

runs and does not fail.

• A history DTC clears after 40 consecutive driving

cycles without a fault. Or clear with the scan tool.

Notice:

• The glow relay is commanded OFF with ignition

ON and engine OFF when the engine coolant
temperature is reached at 30°C (86°F).

• The glow relay is commanded OFF with engine

run when the engine coolant temperature is
reached at 60°C (140°F).

DTC P0380 (Symptom Code 8) (Flash Code 66)
Schematic Reference: Engine Controls Schematics
Connector End View Reference: Engine Controls
Connector End Views or Engine Control Module (ECM)
Connector End Views

Step Action

Value(s)

Yes

No

1

Did you perform the Diagnostic System Check-
Engine Controls?



Go to Step 2

Go to Diagnostic

System Check-

Engine Controls

2

1. Install the scan tool.
2. Turn ON the ignition, with the engine OFF.
3. Perform the Glow Relay test with the scan tool.
4. Command the Glow Relay ON with the scan tool.
Does the glow relay click when commanded ON with
the scan tool?



Go to Diagnostic

Aids

Go to Step 3

3

1. Turn OFF the ignition.
2. Replace the glow relay with the starter relay or

replace with a known good relay.

3. Turn ON the ignition, with the engine OFF.
4. Command the Glow Relay ON with the scan tool.
Does the glow relay click when commanded ON with
the scan tool?



Go to Step 5

Go to Step 4

4

1. Test the control circuit of the glow relay between

the engine control module (ECM) (pin 94 of C-57
connector) and the glow relay (pin 3 of X-5
connector) for a short to battery or ignition
voltage.

2. Repair the circuit(s) as necessary.
Did you find and correct the condition?



Go to Step 7

Go to Step 6

5

Replace the glow relay.
Did you complete the replacement?



Go to Step 7



6

Important: Replacement ECM must be
programmed.
Replace the ECM. Refer to Engine Control Module
(ECM) Replacement in this section.
Did you complete the replacement?



Go to Step 7



6E-140 Engine Control System (4JH1)

Step Action

Value(s)

Yes

No

7

1. Reconnect all previously disconnected relay or

harness connector(s).

2. Clear the DTCs with the scan tool.
3. Turn OFF the ignition for 30 seconds.
4. Cool down the engine as necessary (allow

engine coolant temperature to cool down at least
50

°C [122°F]).

5. Start the engine.
6. Monitor the DTC Information with the scan tool.
Did the DTC fail this ignition?



Go to Step 2

Go to Step 8

8

Observe the DTC Information with the scan tool.
Are there any DTCs that you have not diagnosed?



Go to Diagnostic

Trouble Code (DTC)

List System

OK

Engine Control System (4JH1) 6E-141

DTC P0381 (Symptom Code 4) (Flash Code 67)

Circuit Description
The glow indicator lamp is located on the instrument
panel cluster (IPC). The glow control system is operated
when the engine coolant temperature is low, which
allows easier engine starting. If the ignition switch is
turned ON when the engine coolant temperature is low,
the engine control module (ECM) illuminates the glow
indicator lamp and turns ON the glow plugs. After a
fixed time passes, the ECM turns OFF the glow
indicator lamp and the glow plugs. The ECM monitors
the glow indicator lamp control circuit for conditions that
are incorrect for the commanded state of the glow
indicator lamp. If the ECM detects an open circuit or
short to ground on the glow indicator control circuit, this
DTC will set.
Condition for Running the DTC

• The ignition switch is ON.

Condition for Setting the DTC

• The ECM detects that the low voltage condition on

the glow indicator lamp control circuit for longer
than 3 seconds when the lamp is commanded
OFF.

Action Taken When the DTC Sets

• The ECM illuminates the malfunction indicator

lamp (MIL) when the diagnostic runs and fails.

Condition for Clearing the MIL/DTC

• The ECM turns OFF the MIL when the diagnostic

runs and does not fail.

• A history DTC clears after 40 consecutive driving

cycles without a fault. Or clear with the scan tool.

Diagnostic Aids

• If an intermittent condition is suspected, refer to

Intermittent Conditions in this section.

Notice:

• The glow indicator lamp is commanded OFF with

the ignition ON and engine OFF when the engine
coolant temperature is reached at 30°C (86°F).

DTC P0381 (Symptom Code 4) (Flash Code 67)
Schematic Reference: Engine Controls Schematics
Connector End View Reference: Engine Controls
Connector End Views or Engine Control Module (ECM)
Connector End Views

Step Action

Value(s)

Yes

No

1

Did you perform the Diagnostic System Check-
Engine Controls?



Go to Step 2

Go to Diagnostic

System Check-

Engine Controls

2

1. Install the scan tool.
2. Turn ON the ignition, with the engine OFF.
3. Perform the Glow Indicator test with the scan

tool.

4. Command the Glow Indicator ON with the scan

tool.

Does the glow indicator lamp turn ON when
commanded ON with the scan tool?



Go to Step 3

Go to Step 4

3

Command the Glow Indicator OFF with the scan
tool.
Does the glow indicator lamp OFF?



Go to Step 17

Go to Step 10

4

1. Turn OFF the ignition.
2. Inspect the Meter (15A) fuse (C-14) in the cabin

fuse block.

Is the Meter (15A) fuse (C-14) open?



Go to Step 5

Go to Step 6

5

Replace the Meter (15A) fuse (C-14). If the fuse
continues to open, repair the short to ground on one
of the circuits that fed by the Meter (15A) fuse (C-14)
or replace the shorted attached component fed by
the Meter (15A) fuse (C-14).
Did you complete the repair?



Go to Step 19

