Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Manual — part 1126
3F–34
INTELLIGENT SUSPENSION
Removal
1. Disconnect the battery ground cable.
2. Disconnect the connector from the harness and
remove the connector from the bracket.
3. Remove the clip.
View B
450RY00005
EndOFCallout
1. Remove 2 screws.
2. Disconnect the actuator.
3. Remove the nut (3).
4. Disconnect bracket.
5. Remove the nut (5).
6. Disconnect the washer.
7. Remove the shock absorber.
Refer to Shock Absorber in this section.
Inspection and Repair
Refer to shock Abosorber in this section.
Installation
1. Install the shock absorber.
Refer to Shock Absorber in this section.
2. Install the washer and nut (5), then tighten it to the
specified torque.
Torque: 15N·m (11 lb ft)
3. Install the bracket and nut (3), then tighten it to the
specified torque.
Torque: 39N·m (29 lb ft)
NOTE: Fix the lower nut with wrench not to turn and
tighten upper nut.
4. Fit the top of the shock absorber rod in the
connection part of the actuator.
NOTE:
The mating section is width fitting across flats.
If these normally fit, the distance between the
actuator lower face and the bracket upper face is
about 1 mm.
5. Install 2 screws then tighten it to the specified
torque.
3 N·m (26 lbin)
6. Connect the connector to the harness and insert the
connector to the bracket.
7. Connect the actuator harness with the clip.
8. Connect the battery ground cable.
Legend
(1) Screw
(2) Actuator
(3) Nut
(4) Bracket
(5) Nut
(6) Washer
(7) Shock Absorber
INTELLIGENT SUSPENSION
3F–35
Rear Shock Absorber
Rear Shock Absorber and Associated Parts
LH
461R100003
EndOFCallout
Legend
(1) Connector
(2) Clip
(3) Rear Shock Absorber
(4) Bracket
(5) Bolt
(6) G-Sensor
(7) Front
(8) Upper
(9) Right
(10) Connector
(11) Gusset
3F–36
INTELLIGENT SUSPENSION
Removal
1. Disconnect the battery ground cable.
2. Disconnect the connector (1) from the harness and
remove the connector (1) from the bracket (4).
3. Remove the clip (2).
4. Remove the rear shock absorber (3).
Refer to Shock Absorber in this section.
5. Disconnect the connector (10) from the harness and
remove the connector (10) from the gusset (11).
6. Remove the 2 Bolts (5).
7. Disconnect the G-sensor (6).
Inspection and Repair
Refer to Shock Absorber in this section.
Installation
1. Set the G-sensor on the gusset (11).
2. Install 2 bolts (5) then tighten it to the specified
torque.
Torque: 7 N·m (61 lb in)
3. Connect the connector (10) to the harness and
insert the connector (10) to the gusset (11).
4. Install the rear shock absorber (3).
Refer to Shock Absorber in this section.
5. Connect the connector (1) to the harness and insert
the connector (1) to the bracket (4).
6. Insert the clip (2) to the bracket (4).
7. Connect the battery ground cable.
DIFFERENTIAL (FRONT)
4A1–1
RODEO
DRIVELINE/AXLE
CONTENTS
Differential (Front) . . . . . . . . . . . . . . . . . . . . .
4A1
Differential (Rear) . . . . . . . . . . . . . . . . . . . . .
4A2
Driveline Control System . . . . . . . . . . . . . . . .
4B
Drive Shaft System . . . . . . . . . . . . . . . . . . . .
4C
Transfer Case . . . . . . . . . . . . . . . . . . . . . . . .
4D
CONTENTS
DIFFERENTIAL (FRONT)
Service Precaution. . . . . . . . . . . . . . . . . . . . .
4A1–1
Front Drive Axle . . . . . . . . . . . . . . . . . . . . . . .
4A1–2
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . .
4A1–2
Pinion Shaft Oil Seal . . . . . . . . . . . . . . . . . . .
4A1–3
Pinion Shaft Oil Seal and Associated Parts
4A1–3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .
4A1–3
Inspection and Repair. . . . . . . . . . . . . . . . .
4A1–4
Installation . . . . . . . . . . . . . . . . . . . . . . . . .
4A1–4
Front Drive Axle Assembly . . . . . . . . . . . . . .
4A1–5
Front Drive Axle Assembly and
Associated Parts . . . . . . . . . . . . . . . . . . . . .
4A1–5
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .
4A1–6
Installation. . . . . . . . . . . . . . . . . . . . . . . . . .
4A1–6
Differential Assembly . . . . . . . . . . . . . . . . . . .
4A1–8
Disassembled View . . . . . . . . . . . . . . . . . .
4A1–8
Disassembly . . . . . . . . . . . . . . . . . . . . . . . .
4A1–9
Reassembly . . . . . . . . . . . . . . . . . . . . . . . .
4A1–11
Differential Cage Assembly . . . . . . . . . . . . . .
4A1–19
Disassembled View . . . . . . . . . . . . . . . . . .
4A1–19
Disassembly . . . . . . . . . . . . . . . . . . . . . . . .
4A1–19
Inspection and Repair. . . . . . . . . . . . . . . . .
4A1–20
Reassembly . . . . . . . . . . . . . . . . . . . . . . . .
4A1–20
Main Data and Specifications . . . . . . . . . . . .
4A1–22
Special Tools . . . . . . . . . . . . . . . . . . . . . . .
4A1–25
Service Precaution
WARNING: THIS VEHICLE HAS A SUPPLEMENTAL
RESTRAINT SYSTEM(SRS). REFER TO THE
SRS
COMPONENT AND WIRING LOCATION VIEW IN
ORDER TO DETERMINE WHETHER YOU ARE
PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING. WHEN YOU
ARE REFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING, REFER TO
THE
SRS SERVICE INFOMATION. FAILURE TO
FOLLOW WARNINGS COULD RESULT IN POSSIBLE
AIR BAG DEPLOYMENT, PERSONAL INJURY, OR
OTHERWISE UNNEEDED SRS SYSTEM REPAIRS.
CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
ISUZU will call out those fasteners that require a
replacement after removal. ISUZU will also call out
the fasteners that require thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED , do not
use supplemental coatings (Paints, greases, or
other corrosion inhibitors) on threaded fasteners or
fastener joint interfaces. Generally,such coatings
adversely affect the fastener torque and the joint
clamping force, and may damage the fastener.
When you install fasteners, use the correct
tightening sequence and specification. Following
these instructions can help you avoid damage to
parts and systems.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст