Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Manual — part 1035
EXTERIOR/INTERIOR TRIM
8J–25
Wheel Opening Extension and Rocker Protector Assembly
Wheel Opening Extension, Rocker Protector Assembly and Associated Parts
620RW002
Legend
(1) Front Wheel Opening Extension Assembly
(2) Front Rocker Protector Assembly
(3) Rear Rocker Protector Assembly
(4) Rear Quarter Wheel Opening Extension
Assembly
(5) Rear Door Wheel Opening Extension
Assembly
Removal
1. Remove the front rocker protector assembly.
D
Loosen and pull clips, and remove the front rocker
protector assembly.
2. Remove the rear rocker protector assembly.
D
Loosen and pull three clips, remove a rear screw,
and remove the rear rocker protector assembly.
3. Remove the front wheel opening extension(2).
D
Let a 5mm drill(3) go through four blind rivets(5) to
disengaged riveted portions.
Remove two screws and disengage five clips, then
remove the front wheel opening extension
assembly.
620RS005
8J–26
EXTERIOR/INTERIOR TRIM
4. Remove the rear quarter wheel opening extension
assembly.
D
Let a 5mm drill go through six blind rivets to
disengage riveted portions.
Disengage four clips, remove two screws, and
remove the rear quarter wheel opening extension
assembly.
5. Remove the rear door wheel opening extension
assembly.
D
Let a 5mm drill go through a blind rivet to disengage
riveted portions.
Disengage three clips, peel off the bonded portions
with two double surface adhesive tape and the rear
door wheel opening extension assembly.
Installation
To install, follow the removal steps in the reverse order,
noting the following points.
1. Use a new 2–sided adhesive tape whenever installing
each wheel opening extension assembly and rocker
protector assembly. Using a white gasoline, clean the
places in advance where a 2–sided adhesive tape is
affixed. Also, install the clips, screws and blind rivets
in the order specified as shown in the figure.
620RW001
EXTERIOR/INTERIOR TRIM
8J–27
Mud Flaps (With Wheel Opening Extension)
Mud Flaps (With Wheel Opening Extension) and Associated Parts
620RW003
Legend
(1) Front Bumper Assembly
(2) Front Bumper Slider
(3) Front Mud Flap
(4) Bumper Side Cover
(5) Rear Mud Flap
Removal
Front Side
1. Remove the front bumper assembly.
D
Disconnect the front fog light connector and remove
two bolts from both sides of the front bumper.
2. Remove the front bumper slider(1).
D
Remove two clips(4) and two nuts(3), release the
claw from the washer(2).
601RW009
3. Remove the front mud flap.
D
Remove four nuts and a clip.
601RW013
Rear Side
1. Remove the bumper side cover.
2. Remove the rear mud flap.
D
Remove four bolts and two nuts.
Installation
To install, follow the removal steps in the reverse order.
8J–28
EXTERIOR/INTERIOR TRIM
Ventilation Assembly
Ventilation Assembly and Associated Parts
641RS001
Legend
(1) Outlet Valve Assembly
(2) Ventilation Assembly
Removal
1. Remove the ventilation assembly(1).
D
Pry the ventilation assembly retainers free from the
body panel.
641RS002
2. Remove the outlet valve assembly.
Installation
1. Install the outlet valve assembly.
D
Insert the upper and lower catches of the outlet
valve into the body panel flange and fix them
securely.
2. Install the ventilation assembly.
D
Fix the clips to the body panel securely so that the
ventilation assembly will not come off the body
panel.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст