Nissan Almera Tino V10. Manual — part 172
AT-412
[ALL]
ON-VEHICLE SERVICE
Control Cable Adjustment
ECS009C7
Move selector lever from the “P” position to the “1” position. You
should be able to feel the detentes in each position. If the detentes
cannot be felt or if the pointer indicating the position is improperly
aligned, the control cable needs adjustment.
1.
Place selector lever in “P” position.
2.
Loosen control cable lock nut and place manual shaft in “P”
position.
3.
Pull control cable, by specified force, in the direction of the arrow
shown in the illustration.
4.
Return control cable in the opposite direction of the arrow for 1.0
mm (0.039 in).
5.
Tighten control cable lock nut.
6.
Move selector lever from “P” to “1” position again. Make sure
that selector lever moves smoothly.
7.
Apply grease to contacting areas of selector lever and control
cable. Install any part removed.
Park/Neutral Position (PNP) Switch Adjustment
ECS009C8
1.
Remove control cable end from manual shaft.
2.
Set manual shaft in “N” position.
3.
Loosen PNP switch fixing bolts.
4.
Use a 4 mm (0.157 in) pin for this adjustment.
a.
Insert the pin straight into the manual shaft adjustment hole.
b.
Rotate PNP switch until the pin can also be inserted straight into
hole in PNP switch.
5.
Tighten PNP switch fixing bolts.
6.
Remove pin from adjustment hole after adjusting PNP switch.
7.
Reinstall any part removed.
8.
Adjust control cable. Refer to
AT-412, "Control Cable Adjust-
.
9.
Check continuity of PNP switch. Refer to
PARK/NEUTRAL POSITION (PNP) SWITCH"
.
Specified force: 6.9 N (0.7 kg, 1.5 lb)
AAT980
SAT479J
SAT480J
ON-VEHICLE SERVICE
AT-413
[ALL]
D
E
F
G
H
I
J
K
L
M
A
B
AT
Differential Side Oil Seal Replacement
ECS009C9
1.
Remove drive shaft assemblies. Refer to AX-10, “Drive Shaft”.
2.
Remove oil seals.
3.
Install oil seals.
●
Apply ATF to oil seal surface before installing.
●
Drift for installing
●
Install oil seals so that dimensions “A” and “B” are within
specifications.
Unit: mm (in)
4.
Reinstall any part removed.
Revolution Sensor Replacement
ECS009CA
1.
Disconnect revolution sensor harness connector.
2.
Remove harness bracket from A/T.
3.
Remove revolution sensor from A/T.
4.
Reinstall any part removed.
Always use new sealing parts.
SAT905D
AAT976
A
B
5.5 to 6.5 (0.217 to 0.256)
−
0.5 to 0.5 (
−
0.020 to 0.020)
MCIB9018E
SAT303G
AT-414
[ALL]
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
PFP:00000
Removal
ECS009CB
CAUTION:
Before separating transaxle from engine, remove the crankshaft
position sensor (OBD) from transaxle. Be careful not to damage
sensor.
1.
Remove battery and bracket.
2.
Remove air duct between throttle body and air cleaner.
3.
Disconnect A/T solenoid harness connector, PNP switch har-
ness connector and revolution sensor harness connector.
4.
Remove crankshaft position sensor (OBD) from transaxle.
5.
Drain ATF from transaxle.
6.
Disconnect control cable from transaxle.
7.
Disconnect fluid cooler hoses.
8.
Remove drive shafts. Refer to AX-10, “Drive Shaft”.
9.
Remove the intake manifold support bracket.
10. Remove starter motor from transaxle.
11. Remove upper bolts fixing transaxle to engine.
12. Support transaxle with a jack.
13. Remove center member.
14. Remove center member, engine insulator and engine mounting bracket.
SAT501HA
Tighten bolts to specified torque.
: 41 - 52 N-m (4.2 - 5.3 kg-m, 30 - 38 ft-lb)
SAT304G
AAT469
REMOVAL AND INSTALLATION
AT-415
[ALL]
D
E
F
G
H
I
J
K
L
M
A
B
AT
15. Remove dust cover from converter housing.
Rotate crankshaft to gain access to securing bolts.
16. Remove securing bolts between drive plate and torque con-
verter. when crank shaft rotates, turn to right at the front side of
engine.
17. Support engine with a jack.
18. Remove bolts fixing transaxle to engine.
19. Lower transaxle while supporting it with a jack.
Installation
ECS009CC
1.
Check drive plate runout.
CAUTION:
Do not allow any magnetic materials to contact the ring
gear teeth.
●
If this runout is out of allowance, replace drive plate with ring
gear.
2.
When connecting torque converter to transaxle, measure dis-
tance “A” to be certain that they are correctly assembled.
3.
Install torque converter to drive plate.
●
With converter installed, rotate crankshaft several turns
to check that transaxle rotates freely without binding.
AAT259A
Maximum allowable runout
:
Refer to
.
SAT977H
Distance “A”: 21.1 mm (0.831 in) or more
SAT573D
AAT266A
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст