Nissan Almera Tino V10. Manual — part 6
SBR686C
Precautions
PRECAUTIONS
NLAX0022
I
When installing each rubber part, final tightening must be
carried out under unladen condition* with tires on ground.
*: Fuel, radiator coolant and engine oil full. Spare tire, jack,
hand tools and mats in designated positions.
I
Use flare nut wrench when removing or installing brake
tubes.
I
After installing removed suspension parts, check wheel
alignment.
I
Do not jack up at the trailing arm and lateral link.
I
Always torque brake lines when installing.
Preparation
SPECIAL SERVICE TOOLS
NLAX0032
Tool number
Tool name
Description
KV40104710
Drift
NT474
Install ABS sensor rotor
a: 76.3 mm (3.004 in) dia.
b: 67.9 mm (2.673 in) dia.
ST3072000
Drift
NT115
Install ABS sensor rotor
a: 77 mm (3.03 in) dia.
b: 55.5 mm (2.185 in) dia.
COMMERCIAL SERVICE TOOLS
NLAX0024
Tool name
Description
1 Flare nut crowfoot
2 Torque wrench
NT360
Removing and installing brake piping
a: 10 mm (0.39 in)
GI
MA
EM
LC
EC
FE
CL
MT
AT
SU
BR
ST
RS
BT
HA
SC
EL
IDX
REAR AXLE
Precautions
AX-21
Noise, Vibration and Harshness (NVH)
Troubleshooting
NLAX0025
Refer to “Noise, Vibration and Harshness (NVH) Troubleshooting”,
“FRONT AXLE”, AX-3.
SMA525A
On-vehicle Service
REAR AXLE PARTS
NLAX0026
Check axle and suspension parts for excessive play, wear or dam-
age.
I
Shake each rear wheel to check for excessive play.
SRA690A
REAR WHEEL BEARING
NLAX0027
I
Check axial end play.
Axial end play:
0.05 mm (0.0020 in)
I
Check that wheel hub bearings operate smoothly.
I
Check tightening torque of wheel bearing lock nut.
: 187 - 254 N·m (19 - 26 kg-m, 138 - 188 ft-lb)
I
Replace wheel bearing assembly if there is axial end play or
wheel bearing does not turn smoothly. Refer to “Wheel Hub”,
“REAR AXLE”, AX-23.
REAR AXLE
Noise, Vibration and Harshness (NVH) Troubleshooting
AX-22
Wheel Hub
COMPONENTS
NLAX0028
NAX001
1.
Spindle
2.
Baffle plate
3.
ABS sensor rotor
4.
Wheel hub bearing
5.
Wheel bearing lock nut
6.
Hub cap
7.
ABS sensor
REMOVAL
NLAX0029
CAUTION:
I
Before removing the rear wheel hub assembly, disconnect
the ABS wheel sensor from the assembly. Then move it
away from the hub assembly. Failure to do so may result
in damage to the sensor wires and the sensor becoming
inoperative.
I
Wheel hub bearing does not require maintenance. If any of
the following symptoms are noted, replace wheel hub
bearing assembly.
1)
Growling noise is emitted from wheel hub bearing dur-
ing operation.
2)
Wheel hub bearing drags or turns roughly. This occurs
when turning hub by hand after bearing lock nut is tight-
ened to specified torque.
GI
MA
EM
LC
EC
FE
CL
MT
AT
SU
BR
ST
RS
BT
HA
SC
EL
IDX
REAR AXLE
Wheel Hub
AX-23
SRA711A
1.
Remove brake caliper assembly.
2.
Remove wheel bearing lock nut.
3.
Remove brake rotor (models with disk brake) or brake drum
(models with drum brakes).
4.
Remove wheel hub bearing from spindle.
CAUTION:
Do not disconnect brake hose from caliper.
I
Suspend caliper assembly with wire so as not to stretch
brake hose.
I
Be careful not to depress brake pedal, or piston will pop
out.
Make sure brake hose is not twisted.
ARA082
5.
Remove the sensor rotor using suitable puller, drift and bea
ring replacer.
SAX014
INSTALLATION
NLAX0030
I
With vehicles equipped with ABS, press-fit ABS sensor rotor
into wheel hub bearing using a drift.
Do not reuse ABS sensor rotor. When installing, replace it
with a new one.
SRA734AB
I
Press-fit ABS sensor rotor as far as the location shown in fig-
ure at left.
Height “h”:
12.5 - 13.5 mm (0.492 - 0.531 in)
REAR AXLE
Wheel Hub (Cont’d)
AX-24
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст