Nissan Almera Tino V10. Manual — part 7
SRA712A
I
Install wheel hub bearing.
I
Tighten wheel bearing lock nut.
Before tightening, apply oil to threaded portion of rear spindle.
Do not reuse wheel bearing lock nut.
: 187 - 254 N·m (19 - 26 kg-m, 138 - 188 ft-lb)
I
Check that wheel bearings operate smoothly.
SRA737A
I
Check wheel hub bearing axial end play.
Axial end play:
0.05 mm (0.0020 in)
SFA599B
I
Clinch two places of lock nut.
SRA738A
I
Install hub cap using a suitable tool.
Do not reuse hub cap. When installing, replace it with a
new one.
GI
MA
EM
LC
EC
FE
CL
MT
AT
SU
BR
ST
RS
BT
HA
SC
EL
IDX
REAR AXLE
Wheel Hub (Cont’d)
AX-25
Service Data and Specifications (SDS)
WHEEL BEARING (REAR)
=NLAX0031
Wheel bearing axial end play
mm (in)
0.05 (0.0020)
Wheel bearing lock nut tightening torque
N·m (kg-m, ft-lb)
187 - 254 (19 - 26, 138 - 188)
REAR AXLE
Service Data and Specifications (SDS)
AX-26
CL-1
CLUTCH
C TRANSMISSION/TRANSAXLE
CONTENTS
D
E
F
G
H
I
J
K
L
M
SECTION
CL
A
B
CL
CLUTCH
RS6F51R
PRECAUTIONS . . . . . . . . . . . . . . .. 2
Caution . . . . . . . . . . . . . . . . . . 2
PREPARATION . . . . . . . . . . . . . . ... 3
Special Service Tools . . . . . . . . . . . ... 3
Commercial Service Tool . . . . . . . . . . . 3
NOISE, VIBRATION AND HARSHNESS (NVH)
TROUBLESHOOTING . . . . . . . . . . . . 4
NVH Troubleshooting Chart . . . . . . . . . . 4
CLUTCH PEDAL . . . . . . . . . . . . . . 5
On-Vehicle Inspection and Adjustment . . . . . 5
CLUTCH PEDAL STROKE INSPECTION . . . 5
CLUTCH PEDAL FREE PLAY INSPECTION . ... 5
CLUTCH PEDAL STROKE ADJUSTMENT . . .. 5
CLUTCH PEDAL FREE PLAY ADJUSTMENT . . 6
Removal and Installation . . . . . . . . . . .. 6
INSPECTION AFTER REMOVAL . . . . . . . 7
CLUTCH FLUID . . . . . . . . . . . . . . .. 8
Air Bleeding Procedure . . . . . . . . . . . 8
CLUTCH MASTER CYLINDER . . . . . . . . .. 9
Removal and Installation . . . . . . . . . . .. 9
REMOVAL . . . . . . . . . . . . . . . . 9
INSTALLATION . . . . . . . . . . . . . . 9
Disassembly and Assembly . . . . . . . . ... 10
OPERATING CYLINDER . . . . . . . . . . .. 11
Removal and Installation . . . . . . . . . . 11
REMOVAL . . . . . . . . . . . . . . ... 11
INSTALLATION . . . . . . . . . . . . ... 11
Disassembly and Assembly . . . . . . . . . 11
DISASSEMBLY . . . . . . . . . . . . ... 11
INSPECTION AFTER DISASSEMBLY . . . . 11
ASSEMBLY . . . . . . . . . . . . . . . 12
CLUTCH PIPING . . . . . . . . . . . . . ... 13
Removal and Installation . . . . . . . . . . 13
CLUTCH RELEASE MECHANISM . . . . . . ... 14
Removal and Installation . . . . . . . . . . 14
CLUTCH DISC, CLUTCH COVER AND FLYWHEEL... 16
Removal and Installation . . . . . . . . . . 16
REMOVAL . . . . . . . . . . . . . . ... 16
INSPECTION AND ADJUSTMENT AFTER
REMOVAL . . . . . . . . . . . . . . ... 16
INSTALLATION . . . . . . . . . . . . ... 17
CL-2
[RS6F51R]
PRECAUTIONS
[RS6F51R]
PRECAUTIONS
PFP:00001
Caution
ECS0094X
●
Recommended fluid is brake fluid “DOT 3” or “DOT 4”.
●
Never reuse drained brake fluid.
●
Be careful not to splash brake fluid on painted areas.
●
When removing and installing clutch piping, use Tool.
●
Use new brake fluid to clean or wash all parts of master cyl-
inder and operating cylinder.
●
Never use mineral oils such as gasoline or kerosene. It will
ruin the rubber parts of the hydraulic system.
WARNING:
After cleaning clutch disc, wipe it with a dust collector. Do not
use compressed air.
SBR686C
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст