Nissan Almera Tino V10. Manual — part 1
FRONT & REAR AXLE
CONTENTS
FRONT AXLE . . . . . . . . . . . . . . . . ..2
Precautions . . . . . . . . . . . . . . . . ..2
. . . . . . . . . . . . . . .2
Preparation . . . . . . . . . . . . . . . . ..2
. . . . . . . . . . 2
. . . . . . . . 2
Noise, Vibration and Harshness (NVH)
Troubleshooting . . . . . . . . . . . . . . ...3
. . . . . . . 3
On-vehicle Service. . . . . . . . . . . . . ...3
. . . . . . . . . . . . 3
. . . . . . . . . . .3
. . . . . . . . . . . . . . ...4
Wheel Hub and Knuckle. . . . . . . . . . . ..5
. . . . . . . . . . . . . . .5
. . . . . . . . . . . . . . . . .5
. . . . . . . . . . . . . . ..7
. . . . . . . . . . . . . . ..7
. . . . . . . . . . . . . . . .8
. . . . . . . . . . . . . . . ...8
Drive Shaft . . . . . . . . . . . . . . . . .10
. . . . . . . . . . . . . ...10
. . . . . . . . . . . . . . . ... 11
. . . . . . . . . . . . . . 11
. . . . . . . . . . . . . . 12
. . . . . . . . . . . . . . ...14
. . . . . . . . . . . . . . . .14
Service Data and Specifications (SDS). . . . . .19
. . . . . . . . . . . . . . .19
. . . . . .20
. . . . . . . . . .20
REAR AXLE. . . . . . . . . . . . . . . . ...21
Precautions . . . . . . . . . . . . . . . . 21
. . . . . . . . . . . . . ...21
Preparation . . . . . . . . . . . . . . . . 21
. . . . . . . . . ..21
. . . . . . . ..21
Noise, Vibration and Harshness (NVH)
Troubleshooting . . . . . . . . . . . . . . .22
On-vehicle Service. . . . . . . . . . . . . .22
. . . . . . . . . . .22
Wheel Hub . . . . . . . . . . . . . . . . .23
. . . . . . . . . . . . . ...23
. . . . . . . . . . . . . . . ...23
. . . . . . . . . . . . . . 24
Service Data and Specifications (SDS). . . . . .26
. . . . . . . . . ...26
GI
MA
EM
LC
EC
FE
CL
MT
AT
SU
BR
ST
RS
BT
HA
SC
EL
IDX
SBR686C
Precautions
PRECAUTIONS
NLAX0001
I
When installing rubber parts, final tightening must be car-
ried out under unladen condition* with tires on ground.
*: Fuel, radiator coolant and engine oil full. Spare tire, jack,
hand tools and mats in designated positions.
I
After installing removed suspension parts, check wheel
alignment and adjust if necessary.
I
Use flare nut wrench when removing or installing brake
tubes.
I
Always torque brake lines when installing.
Preparation
SPECIAL SERVICE TOOLS
NLAX0002
Tool number
Tool name
Description
HT72520000
Ball joint remover
NT146
Removing tie-rod outer end and lower ball joint
KV38106800
Differential side oil seal
protector
NT147
Installing drive shaft
KV40107300
Boot band tool
ZZA1229D
Installing boot bands
COMMERCIAL SERVICE TOOLS
NLAX0003
Tool name
Description
1 Flare nut crowfoot
2 Torque wrench
NT360
Removing and installing each brake piping
a: 10 mm (0.39 in)
FRONT AXLE
Precautions
AX-2
Noise, Vibration and Harshness (NVH)
Troubleshooting
=NLAX0004
NVH TROUBLESHOOTING CHART
NLAX0004S01
Use the chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.
Reference page
—
—
—
AX-3,
22
—
—
Possible cause and
SUSPECTED PARTS
Excessive
joint
angle
Joint
sliding
resistance
Imbalance
Improper
installation,
looseness
Parts
interference
Wheel
bearing
damage
DRIVE
SHAFT
AXLE
SUSPENSION
TIRES
ROAD
WHEEL
BRAKES
STEERING
Symptom
DRIVE SHAFT
Noise, Vibration
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
AXLE
Noise
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
Shimmy
×
×
×
×
×
×
×
Judder
×
×
×
×
×
×
Poor quality ride or
handling
×
×
×
×
×
×
×
: Applicable
SMA525A
On-vehicle Service
FRONT AXLE PARTS
NLAX0005
Check front axle and front suspension parts for excessive play,
cracks, wear or other damage.
I
Shake each front wheel to check for excessive play.
I
Make sure that cotter pin is inserted.
I
Retighten all axle and suspension nuts and bolts to the speci-
fied torque.
Tightening torque:
Refer to SU-4, “FRONT SUSPENSION”.
SFA805B
FRONT WHEEL BEARING
NLAX0006
I
Check that wheel bearings operate smoothly.
I
Check axial end play.
Axial end play:
0.05 mm (0.0020 in)
If out of specification or wheel bearing does not turn smoothly,
replace wheel bearing assembly.
Refer to “Wheel Hub and Knuckle”, “FRONT AXLE”, AX-5.
GI
MA
EM
LC
EC
FE
CL
MT
AT
SU
BR
ST
RS
BT
HA
SC
EL
IDX
FRONT AXLE
Noise, Vibration and Harshness (NVH) Troubleshooting
AX-3
SFA108A
DRIVE SHAFT
NLAX0007
Check for grease leakage or other damage.
FRONT AXLE
On-vehicle Service (Cont’d)
AX-4
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст