Nissan Almera Tino V10. Manual — part 3
SFA182A
5.
Check bearing operation.
a.
Add load P with press.
Load P:
49.0 kN
(5.0 ton, 5.5 US ton, 4.92 Imp ton)
b.
Spin knuckle several turns in both directions.
c.
Make sure that wheel bearings operate smoothly.
GI
MA
EM
LC
EC
FE
CL
MT
AT
SU
BR
ST
RS
BT
HA
SC
EL
IDX
FRONT AXLE
Wheel Hub and Knuckle (Cont’d)
AX-9
Drive Shaft
COMPONENTS
=NLAX0016
YAX010
1.
Joint assembly
2.
Boot
3.
Boot band
4.
Circular clip
5.
Drive shaft
6.
Dynamic damper band (where fit-
ted)
7.
Dynamic damper (where fitted)
8.
Boot
9.
Boot band
10. Stopper ring
11. Inner race
12. Cage
13. Ball
14. Snap ring
15. Slide joint housing
16. Circular clip
17. Spider assembly
18. Snap ring
19. Slide joint housing
20. Circular clip
21. Slide joint housing with extension
shaft
22. Dust shield
23. Snap ring
24. Support bearing
25. Support bearing retainer
26. Bracket
27. Snap ring
28. Dust shield
FRONT AXLE
Drive Shaft
AX-10
SFA090A
REMOVAL
NLAX0014
1.
Remove wheel bearing lock nut.
Brake caliper need not be disconnected. Do not twist or
stretch brake hose when moving components.
SFA153B
2.
Remove strut lower mount bolts.
3.
Remove brake hose clip.
SFA499A
4.
Separate drive shaft from knuckle by lightly tapping it. If it is
hard to remove, use a puller.
Cover boots with shop towel so as not to damage them
when removing drive shaft.
Refer to “Wheel Hub and Knuckle”, “FRONT AXLE”, AX-5.
5.
Remove right drive shaft from transaxle.
NAX004
6.
Remove left drive shaft from transaxle.
I
Pry off drive shaft from transaxle as shown at left.
SFA482-D
INSTALLATION
NLAX0015
Transaxle Side
NLAX0015S01
1.
Drive a new oil seal to transaxle. Refer to MT-16 (5MT), MT-11
(6MT) or AT-413.
2.
Set Tool along the inner circumference of oil seal.
GI
MA
EM
LC
EC
FE
CL
MT
AT
SU
BR
ST
RS
BT
HA
SC
EL
IDX
FRONT AXLE
Drive Shaft (Cont’d)
AX-11
SFA483-D
3.
Insert drive shaft into transaxle. Be sure to properly align the
serrations and then withdraw Tool.
4.
Push the drive shaft until the circular clip on the drive shaft fits
into the circular clip groove of the side gear.
5.
After its insertion, try to pull the flange out of the slide joint by
hand. If it pulls out, the circular clip is not properly meshed with
the side gear.
Wheel Side
NLAX0015S02
I
Install drive shaft into knuckle.
I
Tighten upper knuckle nut and wheel bearing lock nut. Refer
to section Installation in “Wheel Hub and Knuckle”, “FRONT
AXLE”, AX-5.
SFA476
DISASSEMBLY
NLAX0017
Transaxle Side (D90 — types)
NLAX0017S01
1.
Remove boot bands.
2.
Put matching marks on slide joint housing and inner race,
before separating joint assembly.
3.
Remove stopper ring with a screwdriver, and pull out slide joint
housing.
SFA514A
4.
Put matching marks on inner race and drive shaft.
5.
Remove snap ring, then remove ball cage, inner race and balls
as a unit.
6.
Draw out boot.
Cover drive shaft serrations with tape so as not to damage the
boot.
SFA963
Transaxle Side (TS79C, T79C, GI2300I & GI3300I)
NLAX0017S04
1.
Remove boot bands.
2.
Put matching marks on slide joint housing and drive shaft
before separating joint assembly.
3.
Put matching marks on spider assembly and drive shaft.
FRONT AXLE
Drive Shaft (Cont’d)
AX-12
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст