Nissan Almera Tino V10. Manual — part 842
EM-24
[QG]
EXHAUST MANIFOLD AND CATALYTIC CONVERTER
Disassembly and Assembly
EBS00QEB
M/T MODELS
A/T MODELS
DISASSEMBLY
1.
Remove catalytic converter cover.
2.
Disconnect exhaust manifold and catalytic converter.
CAUTION:
Be careful not to damage catalytic converter.
ASSEMBLY
●
Assemble in reverse order of disassembly.
YEM049
1.
Exhaust manifold
2.
Catalytic converter
3.
Catalytic converter cover
PBIC0546E
1.
Exhaust manifold
2.
Gasket
3.
Converter cap
4.
Wire mesh washer
5.
Catalytic converter cover
6.
Catalytic converter
7.
Heated oxygen sensor harness
bracket
OIL PAN AND OIL STRAINER
EM-25
[QG]
C
D
E
F
G
H
I
J
K
L
M
A
EM
OIL PAN AND OIL STRAINER
PFP:11110
Removal and Installation
EBS00QEC
REMOVAL
WARNING:
To avoid the danger of being scalded, never drain the engine oil when the engine is hot.
1.
Remove engine RH undercover.
2.
Drain engine oil. Refer to LC-8, “Changing Engine Oil”.
3.
Remove exhaust front tube. Refer to FE-11, “Exhaust System”.
4.
Using a transmission jack, be sure to support the bottom of
transsexual, and remove center member.
5.
Remove gusset and engine rear plate (lower) [A/T vehicle].
6.
Loosen and remove mounting nuts and bolts in reverse order
shown in figure.
MBIA0037E
1.
Oil strainer
2.
Washer
3.
Drain plug
4.
Oil pan
SEM067F
SEM072F
EM-26
[QG]
OIL PAN AND OIL STRAINER
7.
Insert Tool (Seal cutter) between oil pan and cylinder block.
Slide tool by tapping on the side of the tool with a hammer.
Remove oil pan.
8.
Remove oil strainer.
INSTALLATION
1.
Install oil strainer.
NOTE:
Gasket and O-ring are not used for sealed area with oil pump.
2.
Install oil pan drain plug.
●
Referring to “Components”, install drain plug washer.
3.
Apply a continuous bead of liquid gasket to position shown in figure.
Use Genuine Liquid Gasket or equivalent.
4.
Tighten mounting nuts and bolts in order shown in figure.
●
Install mounting nuts and bolts as follows.
5.
Install center member.
Refer to ENGINE ASSEMBLY,
.
6.
Install remaining parts in the reverse order of removal.
INSPECTION AFTER INSTALLATION
●
Check for leakage of engine oil when engine is warmed.
●
Pour engine oil or start engine at least 30 minutes after oil pan is installed.
SEM365EA
PBIC0549E
Mounting bolt:
[Shank length under
head 10 mm (0.39 in)]
: Nos. 1 - 10, 13, 14
[Shank length under
head 12 mm (0.47 in)]
: Nos. 11, 12
SEM072F
IGNITION COIL
EM-27
[QG]
C
D
E
F
G
H
I
J
K
L
M
A
EM
IGNITION COIL
PFP:22448
Removal and Installation
EBS00QED
REMOVAL
1.
Remove ignition coil harness connector from ignition coil.
2.
Remove ignition coil.
CAUTION:
●
Do not shock it.
●
Do not disassemble it.
INSTALLATION
●
Install in the reverse order of removal.
MBIA0038E
1.
Ignition coil
2.
Spark plug
3.
Rocker cover
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст