Nissan Almera Tino V10. Manual — part 908
MT-10
[RS6F51R]
M/T OIL
M/T OIL
PFP:KLD20
Changing M/T Oil
ECS0095N
DRAINING
1.
Start the engine and let it run to warm up the transaxle.
2.
Stop the engine. Remove drain plug and drain oil.
3.
Set a gasket on the drain plug and install it to the transaxle.
CAUTION:
Do not reuse gasket.
FILLING
1.
Remove filler plug. Fill with new oil until oil level reaches the specified limit near filler plug mounting hole.
2.
After refilling oil, check oil level. Assemble gasket to filler plug, then install it to transaxle body.
CAUTION:
Do not reuse gasket.
Checking M/T Oil
ECS0095O
OIL LEAKAGE AND OIL LEVEL
●
Check that oil is not leaking from transaxle or around it.
●
Check oil level from filler plug mounting hole as shown in the fig-
ure.
CAUTION:
Never start engine while checking oil level.
●
Set a new gasket on the filler plug and install it on the transaxle.
CAUTION:
Do not reuse gasket.
Drain plug:
: 30 - 39 N·m (3.1 - 3.9 kg-m, 23 - 28 ft-lb)
Oil grade
: Genuine Nissan gear oil, SAE viscosity
75w - 80 or exact equivalent
Capacity (reference)
: Approx. 2.3
(4 lmp pt)
Filler plug:
: 30 - 39 N·m (3.1 - 3.9 kg-m, 23 - 28 ft-lb)
Filler plug:
: 30 - 39 N·m (3.1 - 3.9 kg-m, 23 - 28 ft-lb)
SCIA0361E
SIDE OIL SEAL
MT-11
[RS6F51R]
D
E
F
G
H
I
J
K
L
M
A
B
MT
SIDE OIL SEAL
PFP:32113
Removal and Installation
ECS0095P
REMOVAL
1.
Remove the drive shaft from the transaxle. Refer to AX-11, “Removal”.
2.
Remove oil seal with a slotted screwdriver.
CAUTION:
Be careful not to damage the case surface when removing
the oil seal.
INSTALLATION
1.
Using a drift (special service tool), drive the oil seal straight until
it protrudes from the case end equal to dimension A shown in
the figure.
Drift to be used:
CAUTION:
●
When installing oil seals, apply multi-purpose grease to oil seal lips.
●
Do not reuse oil seal.
2.
Install all parts in reverse order of removal and check oil level after installation.
SCIA0824E
Dimension A
: Within 0.5 mm of flush with the case.
MCIA0141E
Transaxle case side
ST3072 0000
Clutch housing side
MT-12
[RS6F51R]
POSITION SWITCH
POSITION SWITCH
PFP:32005
Checking
ECS0095Q
BACK-UP LAMP SWITCH
●
Check continuity.
NEUTRAL POSITION SWITCH
●
Check continuity.
Gear position
Continuity
Reverse
Yes
Except reverse
No
SCIA0708E
Gear position
Continuity
Neutral
Yes
Except neutral
No
CONTROL LINKAGE
MT-13
[RS6F51R]
D
E
F
G
H
I
J
K
L
M
A
B
MT
CONTROL LINKAGE
PFP:34103
Removal and Installation of Control Device and Cable
ECS0095R
Refer to the figure for removal and installation procedure.
CAUTION:
●
Keep in mind that the select side lock plate for securing the control cable is different from the one
on the shift side.
●
After assembly, make sure selector lever automatically returns to Neutral when it is moved to 1st,
2nd, or Reverse.
MCIA0120E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст