Nissan Almera Tino V10. Manual — part 134
AT-260
[EXC.F/EURO-OBD]
TROUBLE DIAGNOSIS — INTRODUCTION
4.
4-
3.
Cruise test
AT-277,
"Cruise Test
— Part 1"
Part-1
❏
8. Vehicle Cannot Be Started From D
1
,
.
❏
9. A/T Does Not Shift: D
1
→
D
2
Or Does Not Kickdown: D
4
→
D
2
,
.
❏
10. A/T Does Not Shift: D
2
→
D
3
,
.
❏
11. A/T Does Not Shift: D
3
→
D
4
,
.
❏
12. A/T Does Not Perform Lock-up,
.
❏
13. A/T Does Not Hold Lock-up Condition,
.
❏
14. Lock-up Is Not Released,
.
❏
15. Engine Speed Does Not Return To Idle (Light Braking D
4
→
D
3
),
.
Part-2
AT-280,
"Cruise Test
— Part 2"
❏
16. Vehicle Does Not Start From D
1
,
.
❏
9. A/T Does Not Shift: D
1
→
D
2
Or Does Not Kickdown: D
4
→
D
2
,
.
❏
10. A/T Does Not Shift: D
2
→
D
3
,
.
❏
11. A/T Does Not Shift: D
3
→
D
4
,
.
Part-3
AT-282,
"Cruise Test
— Part 3"
❏
17. A/T Does Not Shift: D
4
→
D
3
When Overdrive Control Switch “ON”
→
“OFF”,
.
❏
15. Engine Speed Does Not Return To Idle (Engine Brake In D
3
),
.
❏
18. A/T Does Not Shift: D
3
→
2
2
, When Selector Lever “D”
→
“2” Position,
.
❏
15. Engine Speed Does Not Return To Idle (Light Braking D
4
→
D
3
),
.
❏
19. A/T Does Not Shift: 2
2
→
1
1
, When Selector Lever “2”
→
“1” Position,
.
❏
20. Vehicle Does Not Decelerate By Engine Brake,
.
❏
21. TCM Self-diagnosis Does Not Activate (PNP & Overdrive Control Switches, and throttle position sen-
sor Circuit Checks),
.
❏
SELF-DIAGNOSTIC PROCEDURE — Mark detected items.
❏
Vehicle speed sensor·A/T (Revolution sensor),
.
❏
Vehicle speed sensor·MTR,
.
❏
Accelerator pedal position (APP) sensor,
.
❏
Shift solenoid valve A,
.
❏
Shift solenoid valve B,
.
❏
Overrun clutch solenoid valve,
.
❏
Torque converter clutch solenoid valve,
.
❏
Batt/fluid temp sen (A/T fluid temperature sensor and TCM power source),
.
❏
Engine speed signal,
.
❏
Line pressure solenoid valve,
.
❏
CAN communication line,
.
❏
Control unit (RAM), control unit (ROM),
.
❏
Control unit (EEP ROM),
.
❏
PNP & overdrive control switches, and throttle position sensor,
.
❏
Battery
❏
Others
5.
❏
For self-diagnosis NG items, inspect each component. Repair or replace the damaged parts.
AT-252,
"SELF-DIAG-
NOSTIC
PROCE-
DURE
(WITHOUT
CONSULT-
II)"
6.
❏
Perform all ROAD TEST and re-mark required procedures.
TROUBLE DIAGNOSIS — INTRODUCTION
AT-261
[EXC.F/EURO-OBD]
D
E
F
G
H
I
J
K
L
M
A
B
AT
Work Flow
ECS0099X
HOW TO PERFORM TROUBLE DIAGNOSES FOR QUICK AND ACCURATE REPAIR
A good understanding of the malfunction conditions can make troubleshooting faster and more accurate. In
general, each customer feels differently about a problem. It is important to fully understand the symptoms or
conditions for a customer complaint.
Make good use of the two sheets provided, “Information From Customer” (
) and “Diagnostic Work-
sheet” (
), to perform the best troubleshooting possible.
7.
❏
Perform the Diagnostic Procedures for all remaining items marked NG. Repair or replace the damaged parts.
Refer to the Symptom Chart when you perform the procedures. (The chart also shows some other possible
symptoms and the component inspection orders.)
AT-285,
"TROUBLE
DIAGNOSIS
— GEN-
ERAL
DESCRIP-
TION"
8.
❏
Erase self-diagnosis code from TCM memories.
AT-251,
"HOW TO
ERASE
SELF-DIAG-
NOSTIC
RESULTS
(WITH CON-
SULT-II)"
256, "HOW
TO ERASE
SELF-DIAG-
NOSTIC
RESULTS
(WITHOUT
CONSULT-
II)"
AT-262
[EXC.F/EURO-OBD]
TROUBLE DIAGNOSIS — INTRODUCTION
WORK FLOW CHART
*1
*2
*3
*4
*5
*6
*7
*8
*9
*10
*11
*12
*13
*14
*15
*16
*17
*18
*19
SAT097KC
TROUBLE DIAGNOSIS — BASIC INSPECTION
AT-263
[EXC.F/EURO-OBD]
D
E
F
G
H
I
J
K
L
M
A
B
AT
TROUBLE DIAGNOSIS — BASIC INSPECTION
PFP:00000
A/T Fluid Check
ECS0099Y
FLUID LEAKAGE CHECK
1.
Clean area suspected of leaking. — for example, mating surface
of converter housing and transmission case.
2.
Start engine, apply foot brake, place selector lever in “D” posi-
tion and wait a few minutes.
3.
Stop engine.
4.
Check for fluid leakage.
FLUID CONDITION CHECK
FLUID LEVEL CHECK
Refer to
.
SAT767B
SAT288G
Fluid color
Suspected problem
Dark or black with burned odor
Wear of frictional material
Milky pink
Water contamination — Road water
entering through filler tube or breather
Varnished fluid, light to dark brown and
tacky
Oxidation — Over or under filling, —
Overheating
SAT638A
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст