Nissan Almera Tino V10. Manual — part 704
INSPECTION/VEHICLE SPEED SIGNAL (WITH ESP
SYSTEM)
=NLEL0448S04
1
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) OUTPUT
Perform ABS actuator and electric unit (control unit) self-diagnosis. Refer to BR-62, “CONSULT-II Functions”.
OK or NG
OK
Replace combination meter.
NG
Check ABS actuator and electric unit (control unit). Refer to BR-70, “Trouble Diagnosis”.
INSPECTION/VEHICLE SPEED SIGNAL (WITHOUT ESP
SYSTEM)
NLEL0448S12
1
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) OUTPUT
Perform ABS actuator and electric unit (control unit) self-diagnosis. Refer to BR-110, “CONSULT-II Functions”.
OK or NG
OK
Replace combination meter.
NG
Check ABS actuator and electric unit (control unit). Refer to BR-97, “Trouble Diagnosis”.
INSPECTION/ENGINE REVOLUTION SIGNAL
NLEL0448S05
1
CHECK ECM SELF-DIAGNOSIS
Perform ECM self-diagnosis. Refer to EC-55, EC-581, EC-958 or EC-1272, “Emission-related Diagnostic Information”.
OK or NG
OK
Replace combination meter.
NG
Perform “Diagnostic Procedure” for displayed DTC.
METERS AND GAUGES
Trouble Diagnoses (Cont’d)
EL-112
INSPECTION/FUEL LEVEL SENSOR UNIT
=NLEL0448S06
1
CHECK GROUND CIRCUIT FOR FUEL LEVEL SENSOR UNIT
1. Turn ignition switch OFF.
2. Disconnect combination meter connector and fuel level sensor unit and fuel pump.
3. Check continuity between combination meter harness connector M84 terminal 26 (B) and fuel level sensor unit and fuel
pump harness connector B38 terminal 1 (B).
4. Check continuity between combination meter harness connector M84 terminal 26 (B) and ground.
YEL332E
OK or NG
OK
©
GO TO 2.
NG
©
Repair harness or connector.
2
CHECK FUEL LEVEL SENSOR UNIT
Refer to “FUEL LEVEL SENSOR UNIT CHECK” (EL-114).
OK or NG
OK
©
GO TO 3.
NG
©
Replace fuel level sensor unit.
3
CHECK HARNESS FOR OPEN OR SHORT
1. Disconnect combination meter connector and fuel level sensor unit and fuel pump connector.
2. Check continuity between combination meter harness connector M84 terminal 25 (G/Y) and fuel level sensor unit and
fuel pump harness connector B38 terminal 4 (G).
3. Check continuity between combination meter harness connector M84 terminal 25 (G/Y) and ground.
YEL333E
OK or NG
OK
©
Fuel level sensor unit and fuel pump is OK.
NG
©
Repair harness or connector.
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
METERS AND GAUGES
Trouble Diagnoses (Cont’d)
EL-113
INSPECTION/WATER TEMPERATURE SIGNAL
NLEL0448S07
1
CHECK ECM SELF-DIAGNOSIS
Perform ECM self-diagnosis. Refer to EC-55, EC-581, EC-958 or EC-1272, “Emission-related Diagnostic Information”.
OK or NG
OK
Replace combination meter.
NG
Perform “Diagnostic Procedure” for display DTC.
SEL498X
Electrical Components Inspection
NLEL0449
FUEL LEVEL SENSOR UNIT CHECK
NLEL0449S02
‰
For removal, refer to FE-6 (QG), FE-20 (YD), “FUEL SYS-
TEM”.
Check the resistance between terminals 4 and 1.
Ohmmeter
Float position
mm (in)
Resistance
value
Ω
(+)
(−)
4
1
*1
Full
139.5 - 145.5
(5.49 - 5.73)
Approx. 4 - 6
*2
1/2
86.7 - 90.7
(3.41 - 3.57)
32 - 33
*3
Empty
10.1 - 12.1
(0.40 - 0.48)
80 - 83
*1 and *3: When float rod is in contact with stopper.
METERS AND GAUGES
Trouble Diagnoses (Cont’d)
EL-114
Schematic
NLEL0450
YEL955D
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
WARNING LAMPS
Schematic
EL-115
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст