Nissan Almera Tino V10. Manual — part 943
SMT066A
7.
Install 3rd & 4th shift fork and bracket, then install 3rd & 4th
fork rod, stopper ring and retaining pin.
When installing stopper rings, use snap ring remover and
installer.
SMT067A
8.
Install interlock balls.
SMT666C
9.
Install 5th shift fork, then install fork rod, stopper ring and
retaining pin.
When installing stopper rings, use snap ring remover and
installer.
SMT018B
10. Install 5th & reverse check plug, spring and ball.
I
Apply sealant to bolt threads. Refer to “Shift Control
Components”, MT-65.
SMT201B
11. Install reverse lock spring on 5th & reverse bracket.
I
Pay attention to its direction.
ASSEMBLY
RS5F50A
MT-86
SMT667C
12. Install check ball and reverse lever spring on reverse lever
assembly.
I
Apply multi-purpose grease to check ball.
I
Pay attention to direction of reverse lever spring.
SMT668C
13. Install reverse lever assembly on clutch housing.
SMT669C
14. Install reverse arm shaft and retaining pin.
SMT670C
15. Hook reverse lock spring and reverse lever spring on reverse
lever assembly.
SMT671C
16. Mesh 4th gear, then install reverse idler gear and shaft.
I
Pay attention to direction of tapped hole.
GI
MA
EM
LC
EC
FE
CL
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ASSEMBLY
RS5F50A
MT-87
SMT070A
17. Place magnet on clutch housing.
SMT446C
18. If bearing preload of mainshaft was adjusted, install selected
shim(s) into transmission case.
I
To aid in installation of transmission case, place shift
selector in the 1st and 2nd shift bracket or between 1st
and 2nd bracket and 3rd and 4th bracket.
19. Apply sealant to mating surface of transmission case and
install it. Refer to “Case Components”, MT-63.
20. Install PNP switch.
SMT626D
21. Apply sealant to threads of check plugs. Install balls, springs
and plugs. Refer to “Shift Control Components”, MT-65.
22. After assembly, check that you can shift into each gear
smoothly.
SAT478EA
23. Measure total turning torque.
Total turning torque (New bearing):
8.8 - 21.6 N·m (90 - 220 kg-cm, 78 - 191 in-lb)
I
When old bearing is used again, preload will be slightly
less than the above. Make sure torque is close to the
specified range.
ASSEMBLY
RS5F50A
MT-88
General Specifications
NLMT0076
TRANSAXLE
NLMT0076S01
Applied model
QG18DE
Model code number
8E009
8E069
Transaxle model
RS5F70A
Number of speeds
5
Synchromesh type
Warner
Shift pattern
Gear ratio
1st
3.333
2nd
1.955
3rd
1.286
4th
0.926
5th
0.733
Reverse
3.214
Number of teeth
Input gear
1st
15
2nd
22
3rd
28
4th
41
5th
45
Rev.
14
Main gear
1st
50
2nd
43
3rd
36
4th
38
5th
33
Rev.
45
Reverse idler gear
37
Oil capacity
(Imp pt)
3.0 (5-1/4)
Oil level (Reference data)
mm (in)
56.5 - 61.0 (2.224 - 2.402)
Remarks
1st & 2nd double baulk ring type synchronizer
Reverse sub-gear
FINAL GEAR
NLMT0076S02
Engine
QG18DE
Transaxle model
RS5F70A
Final gear ratio
4.437
Number of teeth
Final gear/Pinion
71/16
Side gear/Pinion mate gear
14/10
GI
MA
EM
LC
EC
FE
CL
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
SERVICE DATA AND SPECIFICATIONS (SDS)
RS5F70A
General Specifications
MT-89
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст