Nissan Almera Tino V10. Manual — part 572
EC-1114
[YD (WITH EURO-OBD)]
DTC P0336 CKP SENSOR
Diagnostic Procedure
EBS013CT
1.
CHECK GROUND CONNECTIONS
1.
Turn ignition switch OFF.
2.
Loosen and retighten body ground screw. Refer to
.
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace ground connection.
2.
CHECK CKP SENSOR POWER SUPPLY CIRCUIT
1.
Disconnect crankshaft position sensor harness connector.
2.
Turn ignition switch ON.
3.
Check voltage between CKP sensor terminal 3 and ground with
CONSULT-II or tester.
4.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 3.
NG
>> Repair open circuit or short to ground or short to power
in harness or connectors.
3.
CHECK CKP SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check harness continuity between ECM terminal 65 and CKP sensor terminal 2.
Refer to Wiring Diagram.
4.
Also check harness for and short to ground and short to power.
OK or NG
OK
>> GO TO 4.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
MBIB0915E
MBIB0863E
Voltage: Approximately 5.3V
SEF646P
Continuity should exist.
DTC P0336 CKP SENSOR
EC-1115
[YD (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
4.
CHECK CKP SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Check harness continuity between ECM terminal 46 and CKP sensor terminal 1.
Refer to Wiring Diagram.
2.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 5.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
5.
CHECK CRANKSHAFT POSITION SENSOR
Refer to
EC-1115, "Component Inspection"
.
OK or NG
OK
>> GO TO 6.
NG
>> Replace crankshaft position sensor.
6.
CHECK GEAR TOOTH
Visually check for chipping signal plate gear tooth.
OK or NG
OK
>> GO TO 7.
NG
>> Replace the signal plate.
7.
CHECK INTERMITTENT INCIDENT
Refer to
EC-1002, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
.
>> INSPECTION END
Component Inspection
EBS013CU
CRANKSHAFT POSITION SENSOR
1.
Loosen the fixing bolt of the sensor.
2.
Disconnect crankshaft position sensor harness connector.
3.
Remove the sensor.
4.
Visually check the sensor for chipping.
Continuity should exist.
MBIB0864E
EC-1116
[YD (WITH EURO-OBD)]
DTC P0336 CKP SENSOR
5.
Check resistance as shown in the figure.
6.
If NG, replace crankshaft position sensor.
Removal and Installation
EBS013CV
CRANKSHAFT POSITION SENSOR
Refer to
EM-137, "OIL PAN AND OIL STRAINER"
.
Terminal No. (Polarity)
Resistance
Ω
[at 25
°
C (77
°
F)]
3 (+) - 1 (-)
Except 0
3 (+) - 2 (-)
Except 0 or
∞
2 (+) - 1 (-)
Except 0
MBIB0616E
DTC P0340 CMP SENSOR
EC-1117
[YD (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
DTC P0340 CMP SENSOR
PFP:23731
Description
EBS013CW
The camshaft position sensor identifies a particular cylinder by
means of signals from the sensing plate (with five protrusions)
installed to the camshaft. The datum signal output is detected 90
°
signal and sent to the ECM.
ECM Terminals and Reference Value
EBS013CX
Specification data are reference values and are measured between each terminal and ground.
Pulse signal is measured by CONSULT-II.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
: Average voltage for pulse signal (Actual pulse signal can be confirmed by oscilloscope.)
On Board Diagnosis Logic
EBS013CY
MBIB0618E
TERMI-
NAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA
(DC Voltage and Pulse Signal)
45
R
Camshaft position sensor
power supply
[Ignition switch ON]
Approximately 5.3V
47
B
Camshaft position sensor
[Engine is running]
●
Warm-up condition
●
Idle speed
0 - 6V
[Engine is running]
●
Warm-up condition
●
Engine speed is 2,000 rpm
0 - 6V
66
W
Camshaft position sensor
ground
[Ignition switch ON]
Approximately 0.3V
67
B
Sensor ground
(Sensors shield circuit)
[Ignition switch ON]
Approximately 0.3V
MBIB0877E
MBIB0878E
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0340
Camshaft position sensor
circuit
Camshaft position sensor signal is not detect
by the ECM when engine is running.
●
Harness or connectors
(The sensor circuit is open or shorted.)
●
Camshaft position sensor
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст