Nissan Almera Tino V10. Manual — part 573
EC-1118
[YD (WITH EURO-OBD)]
DTC P0340 CMP SENSOR
DTC Confirmation Procedure
EBS013CZ
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
WITH CONSULT-II
1.
Turn ignition switch ON.
2.
Select “DATA MONITOR” mode with CONSULT-II.
3.
Start engine and let it idle for at least 5 seconds.
If engine could not start, keep ignition switch at START position
for 5 seconds.
4.
If 1st trip DTC is detected, go to
.
WITH GST
Follow the procedure “WITH CONSULT-II” above.
SEF817Y
DTC P0340 CMP SENSOR
EC-1119
[YD (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
Wiring Diagram
EBS013D0
YEC505A
EC-1120
[YD (WITH EURO-OBD)]
DTC P0340 CMP SENSOR
Diagnostic Procedure
EBS013D1
1.
CHECK STARTING SYSTEM
Turn ignition switch to START position.
Yes or No
Yes
>> GO TO 2.
No
>> Check starting system. (Refer to SC-13, “STARTING SYSTEM”.)
2.
CHECK GROUND CONNECTIONS
1.
Turn ignition switch OFF.
2.
Loosen and retighten body ground screw. Refer to
.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace ground connection.
3.
CHECK CMP SENSOR POWER SUPPLY CIRCUIT
1.
Disconnect camshaft position (CMP) sensor harness connector.
2.
Turn ignition switch ON.
3.
Check voltage between CMP sensor terminal 1 and ground with
CONSULT-II or tester.
OK or NG
OK
>> GO TO 4.
NG
>> Repair open circuit or short to ground or short to power
in harness or connectors.
Does the engine turn over?
Does the starter motor operate?
MBIB0915E
MBIB0907E
Voltage: Approximately 5.3V
MBIB1095E
DTC P0340 CMP SENSOR
EC-1121
[YD (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
4.
CHECK CMP SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check harness continuity between ECM terminal 66 and CMP sensor terminal 2.
Refer to Wiring Diagram.
4.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 5.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
5.
CHECK CMP SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Check harness continuity between ECM terminal 47 and CMP sensor terminal 3.
Refer to Wiring Diagram.
2.
Also check harness for short to ground or short to power.
OK or NG
OK
>> GO TO 6.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
6.
CHECK CAMSHAFT POSITION SENSOR
Refer to
EC-1121, "Component Inspection"
.
OK or NG
OK
>> GO TO 7.
NG
>> Replace camshaft position sensor.
7.
CHECK INTERMITTENT INCIDENT
Refer to
EC-1002, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
.
>> INSPECTION END
Component Inspection
EBS013D2
CAMSHAFT POSITION SENSOR
1.
Loosen the fixing bolt of the sensor.
2.
Disconnect camshaft position sensor harness connector.
3.
Remove the sensor.
4.
Visually check the sensor for chipping.
Continuity should exist.
Continuity should exist.
MBIB0647E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст