Nissan Almera Tino V10. Manual — part 697
MBIB0906E
CONSULT-II Inspection Procedure
=NLEL0681
“ROOM LAMP”
1.
Turn ignition switch “OFF”.
2.
Connect “CONSULT-II” to the data link connector.
MBIB0233E
3.
Turn ignition switch “ON”.
4.
Touch “START (NISSAN BASED VHCL)”.
YEL322E
5.
Touch “SMART ENTRANCE”.
YEL324E
6.
Touch “ROOM LAMP”.
SEL788W
7.
Select diagnosis mode.
“DATA MONITOR” are available for “ROOM LAMP”.
INTERIOR ROOM LAMP
CONSULT-II Inspection Procedure
EL-84
CONSULT-II Application Items
NLEL0682
ROOM LAMP
Data Monitor Mode
Item (CONSULT-II screen terms)
Diagnosed system
IGNITION SW
Indicates [ON/OFF] condition of ignition switch.
KEY IN DETECT
Indicates [ON/OFF] condition of electronic key switch.
DOOR SW DR RR
Indicates [ON/OFF] condition of rear door switch (driver side).
DOOR SW AS RR
Indicates [ON/OFF] condition of rear door switch (passenger side).
AS DOOR SW
Indicates [ON/OFF] condition of front door switch (passenger side).
DR DOOR SW
Indicates [ON/OFF] condition of front door switch (driver side).
CDL LOCK SW
Indicates [ON/OFF] condition of door lock/unlock switch (lock signal).
CDL UNLOCK SW
Indicates [ON/OFF] condition of door lock/unlock switch (unlock signal).
RKE LOCK
Indicates [ON/OFF] condition of lock signal from remote controller.
RKE UNLOCK
Indicates [ON/OFF] condition of unlock signal from remote controller.
RKE SEL UNLOCK
Indicates [ON/OFF] condition of select unlock signal from remote controller.
KEY CYL LK
Indicates [ON/OFF] condition of lock signal from door key cylinder.
KEY CYL UNLK
Indicates [ON/OFF] condition of unlock signal from door key cylinder.
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
INTERIOR ROOM LAMP
CONSULT-II Application Items
EL-85
Trouble Diagnoses
=NLEL0533
DIAGNOSTIC PROCEDURE 1
NLEL0533S04
Symptom: Interior room lamp timer does not operate
NLEL0533S0401
1
CHECK IGNITION ON SIGNAL
WITH CONSULT-II
Check ignition switch ON signal (“IGNITION SW”) in “DATA MONITOR” mode with CONSULT-II.
MKIB0196E
When ignition switch is ON: IGNITION SW ON
When ignition switch is OFF: IGNITION SW OFF
WITHOUT CONSULT-II
1. Disconnect smart entrance control unit.
2. Check voltage between smart entrance control unit harness connector M100 terminal 29 (Y/G) and ground.
MKIB0072E
MTBL1635
OK or NG
OK
©
GO TO 2.
NG
©
Check the following.
I
10A fuse [No. 10, located in fuse block (J/B)]
I
Harness for open or short between smart entrance control unit and fuse
INTERIOR ROOM LAMP
Trouble Diagnoses
EL-86
2
CHECK DOOR SWITCH INPUT SIGNAL
WITH CONSULT-II
Check driver door switch signal (“DR DOOR SW”) in “DATA MONITOR” mode with CONSULT-II.
MKIB0197E
When driver’s door switch is open: DR DOOR SW ON
When driver’s door switch is closed: DR DOOR SW OFF
WITHOUT CONSULT-II
1. Connect smart entrance control unit connector.
2. Check voltage between smart entrance control unit harness connector M100 terminal 43 (R/W) and ground.
MKIB0073E
MTBL1423
OK or NG
OK
©
GO TO 4.
NG
©
GO TO 3.
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
INTERIOR ROOM LAMP
Trouble Diagnoses (Cont’d)
EL-87
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст