Nissan Almera Tino V10. Manual — part 115
AT-184
[EURO-OBD]
DTC P1705 ACCELERATOR PEDAL POSITION (APP) SENSOR
DIAGNOSTIC TROUBLE CODE (DTC) CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DIAGNOSTIC TROUBLE CODE CONFIRMATION PROCEDURE” has been previously conducted,
always turn ignition switch “OFF” and wait at least 5 seconds before conducting the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
With CONSULT-II
1.
Turn ignition switch “ON” and select “DATA MONITOR” mode for
“A/T” with CONSULT-II.
2.
Check the following.
If the check result is NG, go to
AT-187, "Diagnostic Procedure"
.
If the check result is OK, go to following step.
3.
Turn ignition switch “ON” and select “DATA MONITOR” mode for
“ENGINE” with CONSULT-II.
4.
Start engine and maintain the following conditions for at least 3
consecutive seconds. Then release accelerator pedal com-
pletely.
VHCL SPEED SE: 10 km/h (6 MPH) or more
THRTL POS SEN: Approximately 3V or less
Selector lever: D position (OD “ON”)
If the check result is NG, go to
AT-187, "Diagnostic Procedure"
.
If the check result is OK, go to following step.
SAT014K
SAT971J
Accelerator pedal condition
THRTL POS SEN
Fully released
Less than 4.7V
Partially depressed
0.1 - 4.6V
Fully depressed
1.9 - 4.6V
SAT014K
DTC P1705 ACCELERATOR PEDAL POSITION (APP) SENSOR
AT-185
[EURO-OBD]
D
E
F
G
H
I
J
K
L
M
A
B
AT
5.
Maintain the following conditions for at least 3 consecutive sec-
onds. Then release accelerator pedal completely.
VHCL SPEED SE: 10 km/h (6 MPH) or more
Accelerator pedal: Wide open throttle
Selector lever: D position (OD “ON”)
With GST
Follow the procedure “With CONSULT-II”.
SAT020K
AT-186
[EURO-OBD]
DTC P1705 ACCELERATOR PEDAL POSITION (APP) SENSOR
Wiring Diagram — AT — TPS
ECS0098M
YAT381A
DTC P1705 ACCELERATOR PEDAL POSITION (APP) SENSOR
AT-187
[EURO-OBD]
D
E
F
G
H
I
J
K
L
M
A
B
AT
Diagnostic Procedure
ECS0098N
1.
CHECK DTC WITH ECM
Refer to
EC-55, "Emission-related Diagnostic Information"
.
OK or NG
OK (With CONSULT-II)>>GO TO 2
OK (Without CONSULT-II)>>GO TO 3
NG
>> Check accelerator pedal position sensor circuit for engine control. Refer to
.
2.
CHECK INPUT SIGNAL (WITH CONSULT-II)
With CONSULT-II
1.
Turn ignition switch to “ON” position.
(Do not start engine.)
2.
Select “TCM INPUT SIGNALS” in “DATA MONITOR” mode for
“A/T” with CONSULT-II.
3.
Read out the value of “THRTL POS SEN”.
OK or NG
OK
>> GO TO 4
NG
>> Check harness for short or open between ECM and TCM regarding throttle position sensor circuit.
(Main harness)
SAT014K
Voltage:
Fully-closed throttle:
Approximately 0.5V
Fully-open throttle:
Approximately 4V
SAT614J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст