Nissan Almera Tino V10. Manual — part 185
AT-464
[ALL]
REPAIR FOR COMPONENT PARTS
3.
Remove snap ring.
4.
Remove drive plates, driven plates and retaining plate.
5.
Set Tool on spring retainer and remove snap ring from high
clutch drum while compressing return springs.
●
Set Tool directly over springs.
●
Do not expand snap ring excessively.
6.
Remove spring retainer and return springs.
●
Do not remove return spring from spring retainer.
7.
Remove piston from high clutch drum by turning it.
8.
Remove D-ring and oil seal from piston.
SAT178D
AAT683
SAT302E
SAT189D
SAT139E
REPAIR FOR COMPONENT PARTS
AT-465
[ALL]
D
E
F
G
H
I
J
K
L
M
A
B
AT
INSPECTION
High Clutch Snap Ring, Spring Retainer and Return Springs
●
Check for deformation, fatigue or damage.
●
If necessary, replace.
●
When replacing spring retainer and return springs, replace them as a set.
High Clutch Drive Plates
●
Check facing for burns, cracks or damage.
●
Measure thickness of facing.
●
If not within wear limit, replace.
High Clutch Piston
●
Make sure that check balls are not fixed.
●
Apply compressed air to check ball oil hole opposite the return
spring. Make sure there is no air leakage.
●
Apply compressed air to oil hole on return spring side to make
sure that air leaks past ball.
Seal Ring Clearance
●
Install new seal rings onto input shaft.
●
Measure clearance between seal ring and ring groove.
●
If not within allowable limit, replace input shaft assembly.
ASSEMBLY
1.
Install D-ring and oil seal on piston.
●
Take care with the direction of the oil seal.
●
Apply ATF to both parts.
Thickness of drive plate:
Standard value 2.0 mm (0.079 in)
Wear limit 1.8 mm (0.071 in)
SAT162D
SAT186D
Standard clearance: 0.08 - 0.23 mm (0.0031 - 0.0091 in)
Allowable limit: 0.23 mm (0.0091 in)
SAT187D
SAT182DA
AT-466
[ALL]
REPAIR FOR COMPONENT PARTS
2.
Install piston assembly by turning it slowly.
●
Apply ATF to inner surface of drum.
3.
Install return springs and spring retainer on piston.
4.
Set Tool on spring retainer and install snap ring while compress-
ing return springs.
●
Set Tool directly over return springs.
●
Do not align snap ring gap with spring retainer stopper.
5.
Install drive plates, driven plates and retaining plate.
●
Take care with the order and direction of plates.
6.
Install snap ring.
SAT189D
SAT191D
AAT683
SAT193D
SAT195D
REPAIR FOR COMPONENT PARTS
AT-467
[ALL]
D
E
F
G
H
I
J
K
L
M
A
B
AT
7.
Measure clearance between retaining plate and snap ring. If not
within allowable limit, select proper retaining plate.
8.
Check operation of high clutch.
Refer to
.
9.
Install seal rings to input shaft.
●
Apply petroleum jelly to seal rings.
●
Always replace when removed.
●
Roll paper around seal rings to prevent seal rings from
spreading.
Specified clearance:
Standard 1.4 - 1.8 mm (0.055 - 0.071 in)
Allowable limit 2.4 mm (0.094 in)
Retaining plate:
Refer to
AT-519, "SERVICE DATA AND SPECIFICA-
.
SAT199D
SAT196D
SAT197D
SAT198D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст