Nissan GT-R (2007-2014 year). EXTERIOR / FRONT AXLE / FUEL SYSTEM. Service Manual — part 4
DOOR OUTSIDE MOLDING
EXT-49
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
DOOR OUTSIDE MOLDING
Exploded View
INFOID:0000000009161579
Removal and Installation
INFOID:0000000009161580
REMOVAL
1.
Fully open the door window.
2.
Twist the door outside molding (1) toward the outside of the
vehicle, and then lift up and remove it while disengaging the
pawls.
INSTALLATION
Install in the reverse order of removal.
1.
Door outside molding
2.
Door panel assembly
Refer to
for symbols in the figure.
NNKIA0153ZZ
JMKIA0116GB
Revision: 2012 November
2014 GT-R
EXT-50
< REMOVAL AND INSTALLATION >
DOOR PARTING SEAL
DOOR PARTING SEAL
Exploded View
INFOID:0000000009161581
Removal and Installation
INFOID:0000000009161582
REMOVAL
1.
Fully open the door.
2.
Remove the clips (parting seal clip) of door parting seal (1) with
the remover tool (A).
CAUTION:
Be careful no to damage the body.
3.
Remove the door parting seal from the door assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
1.
Door assembly
2.
Door parting seal
3.
Parting seal clip
4.
Double-faced adhesive tape
[t: 2.0mm (0.079in)]
Refer to
for symbols in the figure.
NNKIA1704ZZ
: Clip
NNKIA0155ZZ
Revision: 2012 November
2014 GT-R
DOOR PARTING SEAL
EXT-51
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
CAUTION:
Visually check the clips for deformation and damage at installation. Replace with new ones if neces-
sary.
Revision: 2012 November
2014 GT-R
EXT-52
< REMOVAL AND INSTALLATION >
REAR WING
REAR WING
Exploded View
INFOID:0000000009161583
Removal and Installation
INFOID:0000000009161584
REMOVAL
1.
Remove the trunk lid finisher inner. Refer to
INT-29, "Removal and Installation"
.
1.
Rear wing assembly
2.
Grommet
3.
Rear wing clip
4.
Center leg bracket
5.
High-mounted stop lamp
6.
Double-faced adhesive tape
[t: 1.6 mm (0.063 in)]
7.
EPT sealer
Refer to
for symbols in the figure.
NNKIA1705ZZ
Revision: 2012 November
2014 GT-R
REAR WING
EXT-53
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
2.
Disconnect the harness connector of trunk lid lock assembly (1)
and the harness connectors (A) of high-mounted stop lamp.
3.
Remove the mounting nuts (A) of rear wing assembly.
4.
Apply protective tape (A) around the outer edge of mating sur-
face between rear wing assembly and trunk lid to prevent from
damage.
5.
Disengage the clips with the remover tool while peeling the double-faced adhesive tape with threads.
CAUTION:
Never bore the rear wing assembly with excessive power. It may cause cracks in the paint.
6.
Replace the following parts after removing the rear wing assembly.
• High-mounted stop lamp: Refer to
EXL-59, "Removal and Installation"
• Clip and grommet for rear wing assembly
• EPT sealer
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Never disassemble the rear wing assembly.
• Replace the double-faced adhesive tape of the back surface with new tape when reusing the rear
wing assembly.
- Remove the double-faced adhesive tape remaining on the rear wing assembly with a double-faced
adhesive tape remover.
- Remove any double-faced adhesive tape remaining on the vehicle side in a similar manner, and then
apply the primer for painted surfaces (Nissan parts dealer).
- Heat the rear wing assembly application surface and panel surface to 20
°
C (68
°
F) or more.
- Press-fit the entire area of the double-faced adhesive tape with 5 kg/cm
2
or more of pressure after
applying the rear wing assembly on the vehicle body.
• Replace the EPT sealer of the back surface with new sealer when reusing the rear wing assembly.
Remove the EPT sealer remaining on the rear wing assembly using a double-faced adhesive tape
remover.
NNKIA0161ZZ
NNKIA0158ZZ
NNKIA0157ZZ
Revision: 2012 November
2014 GT-R
EXT-54
< REMOVAL AND INSTALLATION >
REAR WING
• To maintain adhesion, never wash the vehicle within 24 hours after performing the above work.
Revision: 2012 November
2014 GT-R
FAX-1
TRANSMISSION & DRIVELINE
C
E
F
G
H
I
J
K
L
M
SECTION
FAX
A
B
FAX
N
O
P
CONTENTS
FRONT AXLE
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting Chart . . . . . . . . . ..
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Working Range at a Regular Deal-
ership . . . . . . . . . . . . . . . . . ....
Precautions Necessary for Steering Wheel Rota-
tion After Battery Disconnection . . . . . . . ...
General Precautions . . . . . . . . . . . . .
PERIODIC MAINTENANCE . . . . . . .
FRONT WHEEL HUB AND KNUCKLE . . . .
Inspection . . . . . . . . . . . . . . . . .
FRONT DRIVE SHAFT . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . .
FRONT WHEEL HUB AND KNUCKLE . . . .
Exploded View . . . . . . . . . . . . . . ..
Revision: 2012 November
2014 GT-R
FAX-2
< SYMPTOM DIAGNOSIS >
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000009163148
Use chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference
—
T
h
is
wo
rk i
s
rec
o
m
m
e
n
d
e
d
to
be
p
e
rfo
rme
d
by
G
T
-R ce
rti
fie
d NIS
SAN d
eal
er
.
—
T
h
is
wo
rk i
s
rec
o
m
m
e
n
d
e
d
to
be
p
e
rfo
rme
d
by
G
T
-R ce
rti
fie
d NIS
SAN d
eal
er
.
—
T
h
is
wo
rk i
s
rec
o
m
m
e
n
d
e
d
to
be
p
e
rfo
rme
d
by
G
T
-R ce
rti
fie
d NIS
SAN d
eal
er
.
NVH in F
AX and
FSU
sections
Re
fe
r
to Fron
t
a
x
le
in thi
s
cha
rt.
NVH in WT
section
NVH in WT
section
Re
fe
r to
DRIVE SHA
FT i
n
t
h
is cha
rt.
NVH in BR
section
NVH in ST
section
Possible cause and SUSPECTED PARTS
Ex
ce
ssi
v
e
jo
in
t an
gl
e
Jo
in
t s
lid
in
g re
si
st
a
n
c
e
Im
ba
la
nc
e
Imp
rop
er ins
ta
lla
tio
n
,
lo
os
en
es
s
Part
s interference
Whe
el
be
ari
ng
da
ma
ge
FRONT AXLE AND F
R
ONT
SUSPENSI
ON
FRONT AXL
E
TIRE
ROA
D
WHEEL
DR
IVE SHAF
T
BRAKE
STEERING
Symptom
DRIVE
SHAFT
Noise
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
FRONT
AXLE
Noise
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
×
Shimmy
×
×
×
×
×
×
×
Judder
×
×
×
×
×
×
Poor quality ride or handling
×
×
×
×
×
Revision: 2012 November
2014 GT-R
PRECAUTIONS
FAX-3
< PRECAUTION >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Working Range at a Regular Dealership
INFOID:0000000009186877
CAUTION:
The service items unmentioned on this manual are recommended to be performed by a GT-R certified
NISSAN dealer. Because those service items require special equipment and a GT-R certified technical
staff who completed special training.
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009163149
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precautions Necessary for Steering Wheel Rotation After Battery Disconnection
INFOID:0000000009163150
CAUTION:
Comply with the following cautions to prevent any error and malfunction.
• Before removing and installing any control units, first turn the ignition switch to the LOCK position,
then disconnect both battery cables.
• After finishing work, confirm that all control unit connectors are connected properly, then re-connect
both battery cables.
• Always use CONSULT to perform self-diagnosis as a part of each function inspection after finishing
work. If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
For vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock and
cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the operation pro-
cedure below before starting the repair operation.
OPERATION PROCEDURE
1.
Connect both battery cables.
Revision: 2012 November
2014 GT-R
FAX-4
< PRECAUTION >
PRECAUTIONS
NOTE:
Supply power using jumper cables if battery is discharged.
2.
Turn the ignition switch to ACC position.
(At this time, the steering lock will be released.)
3.
Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
4.
Perform the necessary repair operation.
5.
When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the ignition switch from ACC position to ON position, then to LOCK position. (The steering wheel will lock
when the ignition switch is turned to LOCK position.)
6.
Perform self-diagnosis check of all control units using CONSULT.
General Precautions
INFOID:0000000009163151
CAUTION:
After finishing servicing, check that all the tools and waste are stored in a customary place.
Revision: 2012 November
2014 GT-R
FRONT WHEEL HUB AND KNUCKLE
FAX-5
< PERIODIC MAINTENANCE >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
PERIODIC MAINTENANCE
FRONT WHEEL HUB AND KNUCKLE
Inspection
INFOID:0000000009163156
MOUNTING INSPECTION
Check that the mounting conditions (looseness, back lash) of each component and component conditions
(wear, damage) are normal.
WHEEL BEARING INSPECTION
• Move wheel hub and bearing assembly in the axial direction by hand. Check there is no looseness of wheel
bearing.
• Rotate wheel hub and check is no unusual noise or other irregular conditions. If there is any of abnormal
conditions, replace wheel hub and bearing assembly.
Axial end play
: 0.05 mm (0.002 in) or less
Revision: 2012 November
2014 GT-R
FAX-6
< PERIODIC MAINTENANCE >
FRONT DRIVE SHAFT
FRONT DRIVE SHAFT
Inspection
INFOID:0000000009163157
• Check drive shaft mounting point and joint for looseness and other damage.
• Check boot for cracks and other damage.
CAUTION:
Replace entire drive shaft assembly when noise or vibration occurs from drive shaft.
Revision: 2012 November
2014 GT-R
FRONT WHEEL HUB AND KNUCKLE
FAX-7
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
REMOVAL AND INSTALLATION
FRONT WHEEL HUB AND KNUCKLE
Exploded View
INFOID:0000000009163158
1.
Steering knuckle
2.
Ball seat
3.
Cotter pin
4.
Steering support bracket
5.
Splash guard
6.
Wheel hub and bearing assembly
7.
Spring washer
8.
Wheel hub lock nut
A.
When tightening wheel hub lock nut, tighten the lock nut to 225 N·m (23 kg-m, 166 ft-lb), loosen it, and retighten it to 350 N·m
(36 kg-m, 258 ft-lb) to break in spring washer and the contact surface of wheel hub assembly.
: Apply anti-corrosion.
Refer to
for the symbols in the figure.
JSDIA3973GB
Revision: 2012 November
2014 GT-R
FL-1
ENGINE
C
D
E
F
G
H
I
J
K
L
M
SECTION
FL
A
FL
N
O
P
CONTENTS
FUEL SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Working Range at a Regular Deal-
ership . . . . . . . . . . . . . . . . . ....
Precaution for Battery Service . . . . . . . . ..
REMOVAL AND INSTALLATION . . . .
EVAP CANISTER . . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . . .
Revision: 2012 November
2014 GT-R
FL-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Working Range at a Regular Dealership
INFOID:0000000009164427
CAUTION:
The service items unmentioned on this manual are recommended to be performed by a GT-R certified
NISSAN dealer. Because those service items require special equipment and a GT-R certified technical
staff who completed special training.
Precaution for Battery Service
INFOID:0000000009159997
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.
Revision: 2012 November
2014 GT-R
EVAP CANISTER
FL-3
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
REMOVAL AND INSTALLATION
EVAP CANISTER
Exploded View
INFOID:0000000009160008
Removal and Installation
INFOID:0000000009160009
REMOVAL
1.
Lift up the vehicle.
2.
Remove EVAP canister fixing bolt.
3.
Remove EVAP canister.
NOTE:
The EVAP canister vent control valve and EVAP canister system pressure sensor can be removed without
removing the EVAP canister.
INSTALLATION
Install in the reverse order of removal.
NOTE:
Tighten EVAP canister fixing bolt to the specified torque.
DISASSEMBLY
1.
Turn EVAP canister vent control valve counterclockwise.
2.
Remove the EVAP canister vent control valve.
1.
EVAP canister system pressure sen-
sor
2.
O-ring
3.
EVAP canister
4.
O-ring
5.
EVAP canister vent control valve
Refer to
for symbols not described on the above.
JMBIA0049GB
A
: Lock
B
: Unlock
PBIB2730E
Revision: 2012 November
2014 GT-R
FL-4
< REMOVAL AND INSTALLATION >
EVAP CANISTER
ASSEMBLY
Assemble in the reverse order of disassembly.
CAUTION:
Always replace O-ring with a new one.
Inspection
INFOID:0000000009160010
Check EVAP canister as follows:
1.
Block port (B).
2.
Blow air into port (A) and check that it flows freely out of port (C).
3.
Release blocked port (B).
4.
Apply vacuum pressure to port (B) and check that vacuum pres-
sure exists at the ports (A) and (C).
5.
Block port (A) and (B).
6.
Apply pressure to port (C) and check that there is no leakage.
PBIB2728E
Revision: 2012 November
2014 GT-R
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст