Nissan GT-R (2007-2014 year). EXTERIOR / FRONT AXLE / FUEL SYSTEM. Service Manual — part 3
CENTER MUD GUARD
EXT-33
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
CENTER MUD GUARD
Exploded View
INFOID:0000000009161563
1.
Center mud guard
2.
Grommet
3.
Front bracket
4.
Center bracket
5.
Rear bracket
6.
Wind deflector
NNKIA0140ZZ
Revision: 2012 November
2014 GT-R
EXT-34
< REMOVAL AND INSTALLATION >
CENTER MUD GUARD
Removal and Installation
INFOID:0000000009161564
REMOVAL
1.
Remove the clip (A) from the front edge of the center mud
guard.
2.
Remove the clip (A) from the rear edge of the center mud guard.
3.
Remove the mounting screws on the center mud guard lower surface.
4.
Fully open the door.
5.
Disengage the clips of the center mud guard (1) from vehicle
rear sequentially with the remover tool (A).
CAUTION:
Apply protective tape (B) to the body side to protect from
damage.
6.
Remove the center mud guard from the vehicle body.
7.
Remove the mounting screws after removing the center mud guard, and then remove the front bracket,
center bracket, rear bracket, and wind deflector from the vehicle body.
NOTE:
The front bracket, center bracket, rear bracket, and wind deflector can be removed as a single part.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Check visually the clips for deformation and damage at installation. Replace with new ones if neces-
sary.
• When installing, check that the clips are accurately aligned with the body side panel, then press in.
NNKIA0129ZZ
NNKIA0135ZZ
NNKIA0147ZZ
Revision: 2012 November
2014 GT-R
FLOOR SIDE FAIRING
EXT-35
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
FLOOR SIDE FAIRING
ENGINE UNDER COVER
ENGINE UNDER COVER : Exploded View
INFOID:0000000009161565
NOTE:
This exploded view for VIN < JN1AR54M99M 220041 and VIN < JN1AR54F79M 252231.
NOTE:
1.
Bumper bracket LH
2.
Bumper bracket RH
3.
Bumper fascia
4.
Engine under cover
5.
Hole cover
Refer to
for symbols in the figure.
NNKIA0103GB
Revision: 2012 November
2014 GT-R
EXT-36
< REMOVAL AND INSTALLATION >
FLOOR SIDE FAIRING
This exploded view for VIN > JN1AR54M99M 220041 and VIN > JN1AR54F79M 252231.
ENGINE UNDER COVER : Removal and Installation
INFOID:0000000009161566
REMOVAL
1.
Remove the hole covers.
2.
Remove the clips connecting the engine under cover and the fender protector (front).
3.
Remove the clips (engine undercover rear edge) connected with the engine under cover.
4.
Remove the bolts connecting the radiator core support.
5.
Remove the bolts connecting the bumper brackets (LH,RH).
6.
Remove the bolts connecting the bumper fascia.
7.
Pull the engine under cover toward the rear of the vehicle and remove.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Visually check the clips for deformation and damage at installation. Replace with new ones if neces-
sary.
• Always tighten the mounting bolts to the specified torque.
1.
Bumper bracket LH
2.
Bumper bracket RH
3.
Bumper fascia
4.
Engine under cover
5.
Hole cover
Refer to
for symbols in the figure.
NNKIA1699GB
Revision: 2012 November
2014 GT-R
FLOOR SIDE FAIRING
EXT-37
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
• Be careful to install the hole cover because it may drop in the cover if it is pressed excessively.
FRONT UNDER COVER
FRONT UNDER COVER : Exploded View
INFOID:0000000009161567
FRONT UNDER COVER : Removal and Installation
INFOID:0000000009161568
REMOVAL
1.
Remove the engine under cover. Refer to
EXT-36, "ENGINE UNDER COVER : Removal and Installa-
(Procedure for VIN <JN1AR54M99M 220041/JN1AR54F79M 252231 only)
2.
Remove the clip connecting the front under cover and the fender protector (LH/RH) (front). Refer to
29, "FENDER PROTECTOR : Exploded View"
.
3.
Remove the bolt (front under cover rear edge) tightened together with the floor under cover.
4.
Remove hole cover (engine under cover rear edge).
(Procedure for VIN>JN1AR54M99M 220041/JN1AR54F79M 252231 only)
1.
Radiator core support assembly
2.
Front under cover
3.
Floor under cover
4.
Side member
: Vehicle front
Refer to
for symbols in the figure.
NNKIA0104GB
Revision: 2012 November
2014 GT-R
EXT-38
< REMOVAL AND INSTALLATION >
FLOOR SIDE FAIRING
5.
Remove the bolts (front under cover front edge) connecting the radiator core support.
6.
Remove the front under cover.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Visually check the clips for deformation and damage at installation. Replace with new ones if neces-
sary.
• Always tighten the mounting bolts to the specified torque.
FLOOR UNDER COVER
FLOOR UNDER COVER : Exploded View
INFOID:0000000009161569
FLOOR UNDER COVER : Removal and Installation
INFOID:0000000009161570
REMOVAL
1.
Front side member LH
2.
Suspension member
3.
Front side member RH
4.
Floor under cover
5.
Front cross bar bracket
: Vehicle front
Refer to
for symbols in the figure.
NNKIA0105GB
Revision: 2012 November
2014 GT-R
FLOOR SIDE FAIRING
EXT-39
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
1.
Remove the clip connecting the floor under cover and the fender protector (LH/RH) (rear). Refer to
38, "FLOOR UNDER COVER : Exploded View"
.
2.
Remove the bolt (front under cover rear edge) tightened together with the front under cover.
3.
Remove the floor under cover mounting bolts.
4.
Remove the floor under cover.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• To prevent electric corrosion, always check bolts and washers for surface treatment peeling and
white rust corrosion when mounting bolts of Spec V floor undercover are removed.
• If surface treatment is peeled off, bolts and washers are reusable when contact surfaces between
washer and carbon parts are painted using touch-up paint.Never reuse bolts or washers when white
rust corrosion is detected.
• Always tighten the mounting bolts to the specified torque.
FRONT DIFFUSER
FRONT DIFFUSER : Exploded View
INFOID:0000000009161571
1.
Rear suspension member
2.
Floor assembly
3.
Front diffuser LH
4.
Front diffuser RH
NNKIA1751GB
Revision: 2012 November
2014 GT-R
EXT-40
< REMOVAL AND INSTALLATION >
FLOOR SIDE FAIRING
FRONT DIFFUSER : Removal and Installation
INFOID:0000000009161572
REMOVAL
Front diffuser RH
1.
Remove the bolt (rear diffuser front edge) tighten together with the rear diffuser (center).
2.
Remove the front diffuser RH mounting bolts.
3.
Remove the front diffuser RH.
Front diffuser LH
1.
Remove the bolt (rear diffuser front edge) tighten together with the rear diffuser (center).
2.
Remove the front diffuser LH mounting bolts.
3.
Remove the front diffuser LH.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• When front diffuser mounting bolt is removed, check for surface treatment peel off and oxidation of
mounting bolt and washer so that electric corrosion is prevented.
• Regarding mounting bolt and washer with surface treatment peel off, paint contact surface of washer
and carbon using touch pen or others. By doing so, mounting bolt and washer are reusable. How-
ever, regarding oxidation, never reuse.
• For mounting portion of transmission mounting stay, always replace mounting bolts to new ones in
order to prevent electric corrosion.
• Always tighten the mounting bolts to the specified torque.
REAR DIFFUSER
: Vehicle front
Refer to
for symbols in the figure.
Revision: 2012 November
2014 GT-R
FLOOR SIDE FAIRING
EXT-41
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
REAR DIFFUSER : Exploded View
INFOID:0000000009161573
Rear diffuser construction
NNKIA1752GB
1.
Rear wheel house protector LH
2.
Front diffuser LH
3.
Front diffuser RH
4.
Rear diffuser LH
5.
Rear diffuser (center)
6.
Rear diffuser RH
7.
Rear bumper fascia (lower)
: Vehicle front
Refer to
for symbols in the figure.
Revision: 2012 November
2014 GT-R
EXT-42
< REMOVAL AND INSTALLATION >
FLOOR SIDE FAIRING
Installation position for clip
NNKIA0108GB
1.
Rear wheel well protector LH
2.
Rear diffuser assembly
3.
Rear bumper fascia (lower)
: Vehicle front
Revision: 2012 November
2014 GT-R
FLOOR SIDE FAIRING
EXT-43
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Bracket construction
REAR DIFFUSER : Removal and Installation
INFOID:0000000009161574
CAUTION:
• Never apply any chemical products like wax, coating agent, and compound for carbon parts. They
are produced by composite manufacturing methods similar to a racing vehicle and special paint is
adopted to enhance the look and feel of materials. (Otherwise, water may penetrate to carbon layers
and may cause corrosion.)
• Never place any carbon parts directly on the ground. Always protect them using a soft sheet during
removal, installation, and replacement operations.Never touch carbon parts with oily hands or allow
oil or grease to get on them.
REMOVAL
Rear diffuser (center)
1.
Remove the clips connecting with the rear bumper fascia (lower) lower surface.
2.
Remove the rear diffuser (center) mounting bolts.
3.
Remove the rear diffuser (center).
NNKIA0106GB
1.
Rear panel assembly
2.
Diffuser bracket A LH
3.
Diffuser bracket A RH
4.
Diffuser center bracket
5.
Diffuser bracket B RH
6.
Diffuser bracket B LH
7.
Diffuser bracket C RH
8.
Diffuser bracket C LH
Refer to
for symbols in the figure.
Revision: 2012 November
2014 GT-R
EXT-44
< REMOVAL AND INSTALLATION >
FLOOR SIDE FAIRING
Rear diffuser RH
1.
Remove the rear diffuser (center).
2.
Remove the mounting bolts and clips of rear diffuser RH.
3.
Remove the rear diffuser RH.
Rear diffuser LH
1.
Remove the rear diffuser (center).
2.
Remove the mounting bolts and clips of rear diffuser LH.
3.
Remove the rear diffuser LH.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• When rear diffuser mounting bolt is removed, check for surface treatment peel off and oxidation of
mounting bolt and washer so that electric corrosion is prevented.
• Regarding mounting bolt and washer with surface treatment peel off, paint contact surface of washer
and carbon using touch pen or others. By doing so, mounting bolt and washer are reusable. How-
ever, regarding oxidation, never reuse.
• Visually check the clips for deformation and damage at installation. Replace with new ones if neces-
sary.
• Always tighten the mounting bolts to the specified torque.
Revision: 2012 November
2014 GT-R
ROOF SIDE MOLDING
EXT-45
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
ROOF SIDE MOLDING
Exploded View
INFOID:0000000009161575
Removal and Installation
INFOID:0000000009161576
REMOVAL
Disengage the joint of clips from the roof side molding (1) rear edge
with the remover tool (A).
CAUTION:
Wrap a shop cloth (B) around the remover tool to protect the
body panel from damage.
INSTALLATION
Install in the reveres order of removal.
REMOVAL AND INSTALLATION OF ROOF SIDE MOLDING CLIP
Removal
1.
Remove roof side molding.
1.
Roof side molding
2.
Roof side molding clip
3.
Roof panel
4.
Front pillar finisher
NNKIA0149ZZ
: Clip
JMKIA1246ZZ
Revision: 2012 November
2014 GT-R
EXT-46
< REMOVAL AND INSTALLATION >
ROOF SIDE MOLDING
2.
Heat adhesive tape interface with a dryer, and then peel roof side molding clips with long-nose pliers.
CAUTION:
Be careful not to damage the body.
Installation
1.
Clean tape removed surface with a shop cloth soaked in white gasoline or IPA.
2.
Use two-part epoxy adhesive.
3.
Apply adhesive evenly to clip tape surface.
4.
Position applied parts to the proper location, and then sufficiently press-fit until the adhesive protrudes to
tape side.
5.
Tape clips after press fit, and temporarily hold it for specified time based on the following.
6.
Install from roof side molding rear end to front end in this order after temporarily holding.
CAUTION:
• When installing roof side molding of windshield portion, check that molding fastener is securely
inserted and then press in.
• Never wash the vehicle with in 24 hours so as to keep adhesive.
Adhesive
: 3M–weld DP-100 or equivalent
Thickness
: Approximately 0.5 mm (0.020 in)
Press-fit limit
: 19.6 N
×
2 seconds
5 to 10
°
C (41 to 50
°
F)
: 1 hour or more
11 to 23
°
C (52 to 73
°
F)
: 30 minutes or more
24
°
C or more (75
°
F or more)
: 15 minutes or more
Revision: 2012 November
2014 GT-R
FRONT PILLAR FINISHER
EXT-47
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
FRONT PILLAR FINISHER
Exploded View
INFOID:0000000009161577
Removal and Installation
INFOID:0000000009161578
REMOVAL
1.
Remove the mounting clips and the double-faced adhesive tape of the body side weather-strip.
2.
Remove the body side weather-strip.
NOTE:
Disengage the joint of front pillar clip while sliding upward.
3.
Remove the mounting screws (A) and the clip (B), and then
remove the weather-strip retainer (1).
1.
Front pillar finisher
2.
Weather-strip retainer
3.
Body side weather-strip
4.
Grommet
: Clip
Refer to
NNKIA0150ZZ
NNKIA0151ZZ
Revision: 2012 November
2014 GT-R
EXT-48
< REMOVAL AND INSTALLATION >
FRONT PILLAR FINISHER
4.
Insert the remover tool (A) from the rear edge of the front pillar
finisher (1), and then disengage the clips toward vehicle front.
CAUTION:
Apply protective tape (B) to the body side to protect from
damage.
5.
Remove the front door finisher from the vehicle body.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• During installation check that the clips are aligned with the vehicle body side panel holes, and then
press.
• Never reuse the body side weather-strip.
• To maintain adhesion, never wash the vehicle within 24 hours after installing the body side weather-
strip.
: Clip
NNKIA1738ZZ
Revision: 2012 November
2014 GT-R
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст