Nissan Murano Z51. Manual — part 1447
PRECAUTIONS
TM-139
< PRECAUTION >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• When connecting or disconnecting pin connectors into or
from TCM, do not damage pin terminals (bend or break).
Check that there are not any bends or breaks on TCM pin ter-
minal, when connecting pin connectors.
• Perform TCM input/output signal inspection and check
whether TCM functions normally or not before replacing TCM.
.
• Perform “DTC Confirmation Procedure” after performing each
TROUBLE DIAGNOSIS.
If the repair is completed the DTC should not be displayed in
the “DTC Confirmation Procedure”.
• Always use the specified brand of CVT fluid. Refer to
NORTH AMERICA : Fluids and Lubricants"
.
• Use lint-free paper, not cloth rags, during work.
• Dispose of the waste oil using the methods prescribed by law, ordi-
nance, etc. after replacing the CVT fluid.
FOR USA AND CANADA : Service Notice or Precaution
INFOID:0000000005514089
OBD-II SELF-DIAGNOSIS
• CVT self-diagnosis is performed by the TCM in combination with the ECM. The results can be read through
the blinking pattern of the Malfunction Indicator Lamp (MIL). Refer to the table on
for the indicator used to display each self diagnostic results.
• The self diagnostic results indicated by the MIL are automatically stored in both the ECM and TCM memo-
ries.
Always perform the procedure on
TM-34, "Diagnosis Description"
to complete the repair and avoid
unnecessary blinking of the MIL.
For details of OBD-II, refer to
EC-102, "Diagnosis Description"
• Certain systems and components, especially those related to OBD, may use the new style slide-lock-
ing type harness connector. For description and how to disconnect, refer to
FOR USA AND CANADA : ATFTEMP COUNT Conversion Table
INFOID:0000000005514090
SEF291H
MEF040DA
SEF217U
ATFTEMP COUNT
Temperature
°
C (
°
F)
ATFTEMP COUNT
Temperature
°
C (
°
F)
4
–30 (–22)
177
90 (194)
8
–20 (–4)
183
95 (203)
13
–10 (14)
190
100 (212)
17
–5 (23)
196
105 (221)
TM-140
< PRECAUTION >
[CVT: RE0F09B]
PRECAUTIONS
FOR MEXICO
FOR MEXICO : Precaution for Supplemental Restraint System (SRS) "AIR BAG" and
"SEAT BELT PRE-TENSIONER"
INFOID:0000000005593814
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIR BAG”.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s)
with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly
causing serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
FOR MEXICO : Precaution Necessary for Steering Wheel Rotation after Battery Dis-
connect
INFOID:0000000005593803
NOTE:
• Before removing and installing any control units, first turn the push-button ignition switch to the LOCK posi-
tion, then disconnect both battery cables.
21
0 (32)
201
110 (230)
27
5 (41)
206
115 (239)
32
10 (50)
210
120 (248)
39
15 (59)
214
125 (257)
47
20 (68)
218
130 (266)
55
25 (77)
221
135 (275)
64
30 (86)
224
140 (284)
73
35 (95)
227
145 (293)
83
40 (104)
229
150 (302)
93
45 (113)
231
155 (311)
104
50 (122)
233
160 (320)
114
55 (131)
235
165 (329)
124
60 (140)
236
170 (338)
134
65 (149)
238
175 (347)
143
70 (158)
239
180 (356)
152
75 (167)
241
190 (374)
161
80 (176)
243
200 (392)
169
85 (185)
—
—
ATFTEMP COUNT
Temperature
°
C (
°
F)
ATFTEMP COUNT
Temperature
°
C (
°
F)
PRECAUTIONS
TM-141
< PRECAUTION >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• After finishing work, confirm that all control unit connectors are connected properly, then re-connect both
battery cables.
• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
For vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock and
cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the operation pro-
cedure below before starting the repair operation.
OPERATION PROCEDURE
1.
Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2.
Turn the push-button ignition switch to ACC position.
(At this time, the steering lock will be released.)
3.
Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
4.
Perform the necessary repair operation.
5.
When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the push-button ignition switch from ACC position to ON position, then to LOCK position. (The steering
wheel will lock when the push-button ignition switch is turned to LOCK position.)
6.
Perform self-diagnosis check of all control units using CONSULT-III.
FOR MEXICO : Precaution for Procedure without Cowl Top Cover
INFOID:0000000005593804
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.
FOR MEXICO : Precaution for On Board Diagnosis (OBD) System of CVT and Engine
INFOID:0000000005593805
The ECM has an on board diagnostic system. It will light up the malfunction indicator (MIL) to warn the driver
of a malfunction causing emission deterioration.
CAUTION:
• Be sure to turn the ignition switch OFF and disconnect the battery cable from the negative terminal
before any repair or inspection work. The open/short circuit of related switches, sensors, solenoid
valves, etc. will cause the MIL to light up.
• Be sure to connect and lock the connectors securely after work. A loose (unlocked) connector will
cause the MIL to light up due to an open circuit. (Be sure the connector is free from water, grease,
dirt, bent terminals, etc.)
• Be sure to route and secure the harnesses properly after work. Interference of the harness with a
bracket, etc. may cause the MIL to light up due to a short circuit.
• Be sure to connect rubber tubes properly after work. A misconnected or disconnected rubber tube
may cause the MIL to light up due to a malfunction of the EVAP system or fuel injection system, etc.
• Be sure to erase the unnecessary malfunction information (repairs completed) from the TCM and
ECM before returning the vehicle to the customer.
FOR MEXICO : Precaution for TCM and Transaxle Assembly Replacement
INFOID:0000000005593806
CAUTION:
PIIB3706J
TM-142
< PRECAUTION >
[CVT: RE0F09B]
PRECAUTIONS
To replace TCM and transaxle assembly, refer to
TM-8, "ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Service After Replacing TCM and Transaxle Assembly"
.
FOR MEXICO : Removal and Installation Procedure for CVT Unit Connector
INFOID:0000000005593807
REMOVAL
Rotate bayonet ring counterclockwise. Pull out CVT unit harness
connector upward and remove it.
INSTALLATION
1.
Align
∆
marking on CVT unit harness connector terminal body
with
marking on bayonet ring. Insert CVT unit harness con-
nector. Then rotate bayonet ring clockwise.
2.
Rotate bayonet ring clockwise until
∆
marking on CVT unit har-
ness connector terminal body is aligned with the slit on bayonet
ring as shown in the figure (correctly fitting condition). Install
CVT unit harness connector to CVT unit harness connector ter-
minal body.
CAUTION:
• Securely align
∆
marking on CVT unit harness connector
terminal body with bayonet ring slit. Then, be careful not
to make a half fit condition as shown in the figure.
• Never mistake the slit of bayonet ring for other dent por-
tion.
SCIA2096E
SCIA2097E
SCIA2098E
SCIA2099E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст