Nissan Murano Z51. Manual — part 488
DLN-86
< SERVICE DATA AND SPECIFICATIONS (SDS)
[REAR PROPELLER SHAFT: 3F63A-EDJ75]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specifications
INFOID:0000000005514241
Propeller Shaft Runout
INFOID:0000000005514242
Unit: mm (in)
Journal Axial Play
INFOID:0000000005514243
Unit: mm (in)
Applied model
AWD
VQ35DE
CVT
Propeller shaft model
3F63A-EDJ75
Number of joints
3
Type of journal bearings
(Non-disassembly type)
1st joint
Shell type
2nd joint
EDJ type
3rd joint
Shell type
Coupling method with transfer
Flange type
Coupling method with rear final drive
Flange type
Shaft length
1st (Spider to EDJ joint center)
1142 mm (44.96 in)
2nd (EDJ joint center to spider)
987 mm (38.86 in)
Shaft outer diameter
1st
63.5 mm (2.500 in)
2nd
75 mm (2.95 in)
Item
Limit
Propeller shaft runout
0.8 (0.031)
Item
Standard
Journal axial play
0 (0)
REAR FINAL DRIVE ASSEMBLY
DLN-87
< SYSTEM DESCRIPTION >
[REAR FINAL DRIVE: R145]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
SYSTEM DESCRIPTION
REAR FINAL DRIVE ASSEMBLY
System Diagram
INFOID:0000000005514244
1.
Companion flange
2.
Electric controlled coupling
3.
AWD solenoid
4.
Center oil seal
5.
Pinion front bearing
6.
Collapsible spacer
7.
Pinion rear bearing
8.
Drive pinion
9.
Side gear
10. Pinion mate gear
11.
Drive gear
12. Pinion mate shaft
13. Side bearing
14. Differential case
JPDID0133ZZ
DLN-88
< SYMPTOM DIAGNOSIS >
[REAR FINAL DRIVE: R145]
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000005514245
Use the chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference
NVH in DLN section
NVH in F
AX,
RAX, FSU and
R
S
U sections
NVH in WT section
NVH in WT section
NVH i
n
F
AX and RAX
secti
o
n
NVH in B
R
section
NVH in S
T
section
Possible cause and SUSPECTED PARTS
Gea
r to
ot
h ro
ug
h
Ge
ar co
nt
a
ct
im
pro
p
e
r
T
o
o
th su
rfac
es
wo
rn
Ba
ck
la
sh
in
co
rrec
t
Com
p
ani
on
fl
an
ge
ex
ce
ss
iv
e
run
ou
t
Ge
ar oi
l im
pro
p
e
r
PROPELLER S
H
AFT
AXLE AND S
U
S
PENSION
TI
RE
ROAD WHEE
L
DRIVE SHAFT
BRAKE
STE
E
RING
Symptom
Noise
×
×
×
×
×
×
×
×
×
×
×
×
×
PRECAUTIONS
DLN-89
< PRECAUTION >
[REAR FINAL DRIVE: R145]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
PRECAUTION
PRECAUTIONS
Service Notice or Precautions for Rear Final Drive
INFOID:0000000005514246
• Check for the correct installation status prior to removal or disassembly. If matching marks are required, be
certain they never interfere with the function of the parts when applied.
• Overhaul should be done in a clean work area, it is preferable to work in dustproof area.
• Before disassembly, using steam or white gasoline, completely remove sand and mud from the exterior of
the unit, preventing them from entering into the unit during disassembly or assembly.
• Check appearance of the disassembled parts for damage, deformation, and unusual wear. Replace them
with a new one if necessary.
• Gaskets, seals and O-rings should be replaced any time when the unit is disassembled.
• In principle, tighten bolts or nuts gradually in several steps working diagonally from inside to outside. If tight-
ening sequence is specified, observe it.
• Clean and flush the parts sufficiently and blow-dry them.
• Be careful not to damage sliding surfaces and mating surfaces.
• When applying sealant, remove the old sealant from the mounting surface; then remove any moisture, oil,
and foreign materials from the application and mounting surfaces.
• Always use shop paper for cleaning the inside of components.
• Avoid using cotton gloves or shop rags to prevent entering of lint.
• During assembly, observe the specified tightening torque, and apply new gear oil, petroleum jelly, or multi-
purpose grease as specified for each vehicle, if necessary.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст