Nissan Murano Z51. Manual — part 489
DLN-90
< PREPARATION >
[REAR FINAL DRIVE: R145]
PREPARATION
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000005514247
The actual shapes of Kent-More tools may differ from those of special service tools illustrated here.
Tool number
(Kent-More No.)
Tool name
Description
KV38100200
(J-26233)
Drift
a: 65 mm (2.56 in) dia.
b: 49 mm (1.93 in) dia.
• Installing front oil seal
• Installing side oil seal
ST27861000
(
—
)
Drift
a: 62 mm (2.44 in) dia.
b: 52 mm (2.05 in) dia.
Installing front oil seal
ST35271000
(J-26091)
Drift
a: 72 mm (2.83 in) dia.
b: 63 mm (2.48 in) dia.
Installing center oil seal
KV40100610
(J-26089)
Drift
a: 63 mm (2.48 in) dia.
b: 54.3 mm (2.138 in) dia.
Removing and installing gear carrier and rear
cover (2 pieces are used)
ST33052000
(
—
)
Drift
a: 22 mm (0.87 in) dia.
b: 28 mm (1.10 in) dia.
Removing side bearing inner race
KV4010520
(
—
)
Drift
a: 39.7 mm (1.563 in) dia.
b: 35 mm (1.38 in) dia.
c: 15 mm (0.59 in) dia.
Installing side bearing inner race
ZZA1143D
ZZA0832D
ZZA0814D
ZZA1000D
ZZA1023D
ZZA1133D
PREPARATION
DLN-91
< PREPARATION >
[REAR FINAL DRIVE: R145]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
KV38108500
(
—
)
Drive pinion socket
• Removing and installing drive pinion nut
• Measuring preload torque
KV38108400
(
—
)
Pinion nut wrench
Removing and installing drive pinion nut
ST17130000
(
—
)
Drift
a: 31.8 mm (1.252 in) dia.
b: 58 mm (2.28 in) dia.
Installing pinion rear bearing outer race
ST33230000
(J-25805-01)
Drift
a: 51 mm (2.01 in) dia.
b: 41 mm (1.61 in) dia.
c: 28.5 mm (1.122 in) dia.
Installing pinion front bearing outer race
ST23860000
(
—
)
Drift
a: 38 mm (1.50 in) dia.
b: 33 mm (1.30 in) dia.
• Installing pinion rear bearing inner race
• Installing pinion front bearing inner race
ST38220000
(
—
)
Press stand
a: 63 mm (2.48 in) dia.
b: 65 mm (2.56 in) dia.
Installing pinion front bearing inner race
Tool number
(Kent-More No.)
Tool name
Description
ZZA1205D
ZZA1206D
ZZA0836D
ZZA1046D
ZZA0534D
ZZA1058D
DLN-92
< PREPARATION >
[REAR FINAL DRIVE: R145]
PREPARATION
Commercial Service Tools
INFOID:0000000005514248
ST3127S000
(J-25765-A)
Preload gauge
Measuring preload torque
KV381086S1
(
—
)
Dummy cover set
1. KV38108610
(
—
)
Dummy cover
2. KV38108621
(
—
)
Dummy cover spacer
3. KV38108630
(
—
)
Dummy cover shim
• Checking backlash
• Checking drive gear runout
• Checking tooth contact
Tool number
(Kent-More No.)
Tool name
Description
ZZA0503D
SDIA2313E
Tool name
Description
Flange wrench
Removing and installing companion flange
lock nut
Power tool
Loosening bolts and nuts
NT771
PBIC0190E
REAR DIFFERENTIAL GEAR OIL
DLN-93
< PERIODIC MAINTENANCE >
[REAR FINAL DRIVE: R145]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
PERIODIC MAINTENANCE
REAR DIFFERENTIAL GEAR OIL
Inspection
INFOID:0000000005514249
OIL LEAKAGE
Check that oil is not leaking from final drive assembly or around it.
OIL LEVEL
• Remove filler plug (1) and check oil level from filler plug mounting
hole as shown in the figure.
CAUTION:
Never start engine while checking oil level.
• Set a new gasket on filler plug and install it on final drive assembly.
.
CAUTION:
Never reuse gasket.
Draining
INFOID:0000000005514250
1.
Stop engine.
2.
Remove drain plug (1) and drain gear oil.
3.
Set a new gasket on drain plug and install it to final drive assem-
bly and tighten to the specified torque. Refer to
CAUTION:
Never reuse gasket.
Refilling
INFOID:0000000005514251
1.
Remove filler plug (1). Fill with new gear oil until oil level reaches
the specified level near filler plug mounting hole.
2.
After refilling oil, check oil level. Set a new gasket to filler plug, then install it to final drive assembly. Refer
to
CAUTION:
Never reuse gasket.
JPDID0164ZZ
JPDID0163ZZ
Oil grade and viscosity
: Refer to
NORTH AMERICA : Fluids
and Lubricants"
(for
"FOR MEXICO : Fluids and
Lubricants"
(for MEXICO).
Oil capacity
: Refer to
JPDID0164ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст