Nissan Murano Z51. Manual — part 639
EM-28
< PERIODIC MAINTENANCE >
COMPRESSION PRESSURE
10. Start the engine, and check that the engine runs smoothly.
11. Perform trouble diagnosis. If DTC appears, erase it. Refer to
ENGINE COVER
EM-29
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
REMOVAL AND INSTALLATION
ENGINE COVER
Exploded View
INFOID:0000000005515924
Removal and Installation
INFOID:0000000005515925
REMOVAL
1.
Remove radiator core support covers (RH and LH) and air duct (inlet). Refer to
.
2.
Remove engine cover mounting bolts (A) and (B).
3.
Draw and pull out engine cover from engine cover mounting bolts (C) and (D).
CAUTION:
Pull engine cover from mounting bolt (D) holding with hand the position (E) as shown in the figure.
4.
Remove engine cover mounting bolts (C) and (D) if necessary.
INSTALLATION
Install in the reverse order of removal.
1.
Engine cover
Refer to
JPBIA1712GB
JPBIA1718ZZ
EM-30
< REMOVAL AND INSTALLATION >
DRIVE BELT AUTO TENSIONER AND IDLER PULLEY
DRIVE BELT AUTO TENSIONER AND IDLER PULLEY
Exploded View
INFOID:0000000005515926
Removal and Installation
INFOID:0000000005515927
Removal
1.
Remove drive belt. Refer to
EM-17, "Removal and Installation"
.
• Keep auto-tensioner pulley arm locked after drive belt is removed.
2.
Remove auto-tensioner and idler pulley.
• Keep auto-tensioner pulley arm locked to install or remove auto-tensioner.
Installation
Install in the reverse order of removal.
CAUTION:
If there is damage greater than peeled paint, replace drive belt auto-tensioner.
1.
Drive belt auto-tensioner
2.
Idler pulley
3.
Idler pulley
4.
Bracket
Refer to
for symbols in the figure.
JPBIA1626GB
AIR CLEANER AND AIR DUCT
EM-31
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
AIR CLEANER AND AIR DUCT
Exploded View
INFOID:0000000005515928
Removal and Installation
INFOID:0000000005515929
REMOVAL
NOTE:
Mass air flow sensor is removable under the car-mounted condition.
1.
Remove radiator core support covers (RH and LH).
2.
Remove air duct (inlet).
3.
Disconnect harness connector from mass air flow sensor.
4.
Disconnect PCV hose.
5.
Remove air cleaner cases (upper and lower) with mass air flow sensor and air duct assembly disconnect-
ing their joints.
• Add mating marks if necessary for easier installation.
1.
Mass air flow sensor
2.
Air cleaner case (upper)
3.
Holder
4.
Air cleaner filter
5.
Clamp
6.
Air duct assembly
7.
Clamp
8.
PCV hose
9.
Air duct (inlet)
10. Grommet
11.
Collar
12. Radiator core support cover (RH)
13. Radiator core support cover (LH)
14. Grommet
15. Grommet
16. Bracket
17. Bracket
18. Collar
19. Grommet
20. Air cleaner case (lower)
A.
To electric throttle control actuator
B.
To rocker cover (bank 2)
Refer to
for symbols in the figure.
JPBIA1670GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст