Nissan Murano Z51. Manual — part 1063
PARKING BRAKE SHOE
PB-5
< PERIODIC MAINTENANCE >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
PARKING BRAKE SHOE
Adjustment
INFOID:0000000005516250
1.
Adjust parking brake pedal stroke. Refer to
PB-3, "Inspection and Adjustment"
2.
Perform parking brake break-in (drag on) operation by driving vehicle under the following conditions:
• Drive forward
• Vehicle speed: Approx. 40 km/h (25 MPH) set (constant and forward)
• Parking brake operating force: Approx. 145 N (15 kg, 33 lb)
• Time: Approx. 10 sec.
CAUTION:
To prevent lining from getting too hot, allow a cool off period of approximately 5 minutes after
every break-in operation.
3.
After the break-in procedure, check parking pedal stroke of parking brake.
CAUTION:
If it is out of the specification, adjust again. Refer to
PB-6
< REMOVAL AND INSTALLATION >
PARKING BRAKE CONTROL
REMOVAL AND INSTALLATION
PARKING BRAKE CONTROL
Exploded View
INFOID:0000000005516251
Removal and Installation
INFOID:0000000005516252
REMOVAL
1.
Remove rear tires with power tool.
2.
Remove instrument panel assembly. Refer to
.
3.
Disconnect parking brake switch harness connector.
4.
Remove adjusting nut and loosen front cable.
5.
Remove device assembly.
6.
Remove rear ventilator duct. Refer to
VTL-62, "REAR FOOT DUCT 2 : Exploded View"
(without 7 inch
display),
VTL-119, "REAR VENTILATOR DUCT 2 : Exploded View"
(with 7 inch display).
7.
Separate front cable from rear cable, and remove front cable and return spring.
8.
Remove parking brake shoe, and remove rear cable from toggle lever. Refer to
9.
Remove rear cable mounting bolts and nuts, pull out rear cable from vehicle.
INSTALLATION
Note the following, Install the reverse order of the removal.
• Never reuse the adjusting nut.
1.
Pin
2.
Rear cable (RH)
3.
Rear cable (LH)
4.
Return spring
5.
Front cable
6.
Parking brake switch
7.
Stopper rubber
8.
Return spring
9.
Silencer
10. Device assembly
11.
Pedal pad
12. Adjusting nut
: Apply multi-purpose grease.
Refer to
for symbols not described on the above.
JPFIB0056GB
PARKING BRAKE CONTROL
PB-7
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
Adjustment
INFOID:0000000005516253
ADJUSTMENT AFTER INSTALLATION
Adjust the parking brake pedal stroke. Refer to
PB-8
< REMOVAL AND INSTALLATION >
PARKING BRAKE SHOE
PARKING BRAKE SHOE
Exploded View
INFOID:0000000005516254
Removal and Installation
INFOID:0000000005516255
REMOVAL
WARNING:
Clean any dust from the parking brake shoes and back plates with a vacuum dust collector. Never
blow with compressed air.
1.
Remove rear tires with power tool.
2.
Remove disc rotor. Refer to
BR-43, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
.
CAUTION:
Parking brake completely in the released position.
3.
If disc rotor cannot be removed, remove as follows:
a.
Fix the disc rotor with wheel nuts and remove the adjusting hole plug.
b.
Using suitable tool, rotate adjuster (1) in direction (B) to retract
and loosen parking brake shoe.
4.
Remove anti-rattle pins, retainers, anti-rattle spring, adjuster
spring and return springs.
CAUTION:
Never drop the removed parts.
5.
Remove parking brake shoes, adjuster assembly and toggle
lever.
CAUTION:
• The parking brake shoes for the front side are made of dif-
ferent materials from those for the rear side. Never misi-
dentify them when removing.
• Never drop the removed parts.
INSTALLATION
Install in the reverse order of removal.
• Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease to the back plate and brake shoe.
1.
Back plate
2.
Parking brake shoe
3.
Adjuster
4.
Adjuster spring
5.
Return spring
6.
Anti-rattle spring
7.
Retainer
8.
Anti-rattle pin
9.
Toggle lever
: Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease.
JPFIB0046ZZ
JPFIB0007ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст