Nissan Murano Z51. Manual — part 1529
WT-54
< PERIODIC MAINTENANCE >
ROAD WHEEL
• Perform the ID registration, after tire rotation. Refer to
ROAD WHEEL TIRE ASSEMBLY
WT-55
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
REMOVAL AND INSTALLATION
ROAD WHEEL TIRE ASSEMBLY
Exploded View
INFOID:0000000005576023
Removal and Installation
INFOID:0000000005576024
REMOVAL
1.
Remove wheel nuts.
2.
Remove tire assembly.
INSTALLATION
Install in the reverse order of removal.
Inspection
INFOID:0000000005514453
ALUMINUM WHEEL
1.
Check tires for wear and improper inflation.
2.
Check wheels for deformation, cracks and other damage. If deformed, remove wheel and check wheel
runout.
a.
Remove tire from aluminum wheel and mount on a tire balance machine.
b.
Set dial indicator as shown in the figure.
c.
If the lateral deflection (A) or vertical deflection (B) for radial
runout value exceeds the limit, replace aluminum wheel.
STEEL WHEEL
1.
Check tires for were and improper inflation.
1.
Tire assembly
Refer to
JSGIA0639GB
Limit
A:
Refer to
B:
Refer to
SEIA0737E
WT-56
< REMOVAL AND INSTALLATION >
ROAD WHEEL TIRE ASSEMBLY
2.
Check wheels for deformation, clacks and other damage. If deformed, remove wheel and check wheel
runout.
a.
Remove tire from steel wheel and mount wheel on a tire balance machine.
b.
Set two dial indicators as shown in the illustration.
c.
Set each dial indicator to “0”.
d.
Rotate wheel and check dial indicators at several points around
the circumference of the wheel.
e.
Calculate runout at each point as shown below.
f.
Select maximum positive runout value and the maximum nega-
tive value. Add the two values to determine total runout.
CAUTION:
In case a positive or negative value is not available, use the
maximum value (negative or positive) for total runout.
g.
If the total runout value exceeds limit, replace steel wheel.
Lateral runout limit (A):
(
+
)/2
Radial runout limit (B):
(
+
)/2
Limit
A:
Refer to
B:
Refer to
SEIA0738E
TRANSMITTER
WT-57
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
TRANSMITTER
Exploded View
INFOID:0000000005514455
Removal and Installation
INFOID:0000000005514456
REMOVAL
1.
Deflate tire. Unscrew transmitter retaining nut and allow transmitter to fall into tire.
2.
Gently bounce tire so that transmitter falls to bottom of tire.
Place on tire changing machine and break both tire beads
ensuring that the transmitter remains at the bottom of the tire.
3.
Turn tire so that valve hole is at bottom and bounce so that
transmitter (1) is near valve hole. Carefully lift tire onto turntable
and position valve hole (and transmitter) 270 degree from
mounting/dismounting head (2).
4.
Lubricate tire well and remove first side of the tire. Reach inside
the tire and remove the transmitter.
INSTALLATION
JPEIC0041GB
1.
Transmitter
2.
Grommet seal
3.
Valve nut
4.
Valve core
5.
Cap
Refer to
for symbols in figure.
SEIA0047E
JPEIC0014GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст