Nissan Murano Z51. Manual — part 1442
TCM
TM-119
< ECU DIAGNOSIS INFORMATION >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
JCDWM0716GB
TM-120
< ECU DIAGNOSIS INFORMATION >
[CVT: RE0F09B]
TCM
JCDWM0717GB
TCM
TM-121
< ECU DIAGNOSIS INFORMATION >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Fail-safe
INFOID:0000000005514078
The TCM has an electrical fail-safe mode. In this mode TCM operates even if there is an error in a main elec-
tronic control input/output signal circuit.
FAIL-SAFE FUNCTION
If any malfunction occurs in a sensor or solenoid valve, this function controls the CVT to make driving possi-
ble.
JCDWM0718GB
TM-122
< ECU DIAGNOSIS INFORMATION >
[CVT: RE0F09B]
TCM
Secondary Speed Sensor
The shift pattern is changed in accordance with the throttle position when an unexpected signal is sent from
the secondary speed sensor to the TCM. The overdrive control mode is inhibited, and the transaxle is put in
“D”.
Primary Speed Sensor
The shift pattern is changed in accordance with the throttle position and secondary speed (vehicle speed)
when an unexpected signal is sent from the primary speed sensor to the TCM. The overdrive control mode is
inhibited, and the transaxle is put in “D”.
Transmission range Switch
If an unexpected signal is sent from the transmission range switch to the TCM, the transaxle is put in “D”.
CVT Fluid Temperature Sensor
If an unexpected signal is sent from the CVT fluid temperature sensor to the TCM, the gear ratio in use before
receiving the unexpected signal is maintained or the gear ratio is controlled to keep engine speed under 5,000
rpm.
Secondary Pressure Sensor
• If an unexpected signal is sent from the secondary pressure sensor to the TCM, the secondary pressure
feedback control is stopped and the offset value obtained before the non-standard condition occurs is used
to control line pressure.
• If secondary pressure sensor error signal is inputted to the TCM, secondary pressure feedback control
stops, but line pressure is controlled normally.
Line Pressure Solenoid Valve
If an unexpected signal is sent from the solenoid valve to the TCM, the line pressure solenoid valve is turned
OFF to achieve the maximum fluid pressure.
Secondary Pressure Solenoid Valve
If an unexpected signal is sent from the solenoid valve to the TCM, the secondary pressure solenoid valve is
turned OFF to achieve the maximum fluid pressure.
Torque Converter Clutch Solenoid Valve
If an unexpected signal is sent from the solenoid valve to the TCM, the torque converter clutch solenoid valve
is turned OFF to cancel the lock-up.
Step Motor
If an unexpected signal is sent from the step motor to the TCM, the step motor coil phases “A” through “D” are
all turned OFF to hold the gear ratio used just before the non-standard condition occurred.
Lock-up Select Solenoid Valve
If an unexpected signal is sent from the solenoid valve to the TCM, the lock-up select solenoid valve is turned
OFF to cancel the lock-up.
TCM Power Supply (Memory Back-up)
Transaxle assembly is protected by limiting the engine torque when the memory back-up power supply (for
controlling) from the battery is not supplied to the TCM. Normal status is restored when turning the ignition
switch OFF to ON after the normal power supply.
DTC Inspection Priority Chart
INFOID:0000000005514079
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
NOTE:
If DTC “U1000” is indicated with other DTCs, start from a diagnosis for DTC “U1000”. Refer to
DTC Index
INFOID:0000000005514080
NOTE:
If DTC “U1000” is indicated with other DTCs, start from a diagnosis for DTC “U1000”. Refer to
Priority
Detected items (DTC)
1
U1000
2
Except above
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст