Nissan Murano Z51. Manual — part 1563
WW-130
< REMOVAL AND INSTALLATION >
FRONT WIPER ARM
FRONT WIPER ARM
Exploded View
INFOID:0000000005516056
Removal and Installation
INFOID:0000000005516057
REMOVAL
1.
Operate the front wiper to move it to the auto stop position.
2.
Open the hood.
3.
Remove front wiper arm caps.
4.
Remove the front wiper arm mounting nuts.
5.
Raise front wiper arm, and remove front wiper arm from the vehicle.
INSTALLATION
1.
Clean wiper arm mount as shown in the figure to prevent nuts
from being loosened.
2.
Operate the front wiper motor to move the front wiper to the auto
stop position.
3.
Adjust the front wiper blade position. Refer to
4.
Install the front wiper arms by tightening the mounting nuts.
5.
Inject the washer fluid.
6.
Operate the front wiper to move it to the auto stop position.
7.
Check that the front wiper blades stop at the specified position.
8.
Install front wiper arm caps.
Adjustment
INFOID:0000000005516058
WIPER BLADE POSITION ADJUSTMENT
Clearance between the end of cowl top cover and the top of front wiper blade center
1.
Front wiper blade (RH)
2.
Front wiper arm (RH)
3.
Front wiper arm cap
4.
Front wiper arm (LH)
5.
Front wiper blade (LH)
Refer to
for symbols in the figure.
JPLIA0874GB
ELH0717D
FRONT WIPER ARM
WW-131
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
Standard clearance
R
: 51.0
±
7.5 mm (2.008
±
0.295 in)
L
: 48.0
±
7.5 mm (1.890
±
0.295 in)
JPLIA0082ZZ
WW-132
< REMOVAL AND INSTALLATION >
WIPER BLADE
WIPER BLADE
Exploded View
INFOID:0000000005516059
Removal and Installation
INFOID:0000000005516060
REMOVAL
Remove the wiper blade from the wiper arm.
INSTALLATION
Install the front wiper blade to the wiper arm.
Replacement
INFOID:0000000005516061
1.
Hold the rip of old wiper refill (1) at the rear end of the wiper
blade with long-nose pliers, and pull out the wiper refill to the
direction (A).
2.
Insert the tip of new wiper refill (1) into the rear end of wiper
blade. Slide the wiper refill to the direction (A) while pressing the
wiper refill onto the wiper blade rear end.
NOTE:
• Insert the wiper refill to be held securely by tab (B) of wiper
blade.
• After the wiper refill is fully inserted, remove the holder
*
(2).
*
: Attached to service parts.
1.
Wiper refill
2.
Wiper blade
3.
Wiper arm
A.
Wiper blade end
B.
Wiper blade tip
JPLIA1587ZZ
JPLIA1583ZZ
JPLIA1584ZZ
WIPER BLADE
WW-133
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
3.
Inert the wiper refill until the stopper at the rear end of wiper refill
fits in the tab. Check that “LOCK” mark on wiper refill is aligned
with “ ” mark on wiper blade.
4.
Untwist the twisted wiper refill (
) at the rear end of wiper
blade, if any.
5.
Check the following items after replacing wiper refill.
• Wiper refill is not twisted at all.
• Wiper refill thoroughly fits in the tab on wiper blade.
• Wiper refill is inserted from the proper direction.
NOTE:
When the vertebra is detached.
• Insert the vertebra (1) into the wiper blade to the same bending
direction.
• If a vertebra has a notch, fit it to a protrusion inside the wiper refill.
JPLIA1585ZZ
JPLIA1586ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст