Nissan Murano Z51. Manual — part 315
BRAKE WARNING LAMP
BRC-83
< DTC/CIRCUIT DIAGNOSIS >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
BRAKE WARNING LAMP
Description
INFOID:0000000005517385
×
: ON –: OFF
NOTE:
• 1: Brake warning lamp will turn on in case of parking brake operation (when switch is ON) or of brake fluid level switch operation
(when brake fluid is insufficient).
• 2: After starting the engine, brake warning lamp is turned off.
Component Function Check
INFOID:0000000005517386
1.
BRAKE WARNING LAMP OPERATION CHECK 1
Check that the lamp illuminates for approximately 2 seconds after the ignition switch is turned ON.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Proceed to diagnosis procedure. Refer to
.
2.
BRAKE WARNING LAMP OPERATION CHECK 2
Check that the brake warning lamp in the combination meter turns ON/OFF correctly when operating the park-
ing brake pedal.
NOTE:
Brake warning lamp will turn on in case of parking brake operation (when switch is ON) or of brake fluid level
switch operation (when brake fluid is insufficient).
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Check parking brake switch. Refer to
.
Diagnosis Procedure
INFOID:0000000005517387
1.
CHECK PARKING BRAKE SWITCH
Check that the brake warning lamp in the combination meter turns ON/OFF correctly when operating the park-
ing brake pedal.
NOTE:
Brake warning lamp will turn on in case of parking brake operation (when switch is ON) or of brake fluid level
switch operation (when brake fluid is insufficient).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check parking brake switch. Refer to
.
2.
CHECK SELF-DIAGNOSIS
Perform self-diagnosis for “ABS” with CONSULT-III.
Is the inspection result normal?
YES
>> Check combination meter. Refer to
MWI-34, "CONSULT-III Function (METER/M&A)"
.
NO
>> Check items displayed by self-diagnosis for “ABS” with CONSULT-III.
Special Repair Requirement
INFOID:0000000005532355
1.
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION AND CALIBRATION OF DECEL G
SENSOR
Condition
Brake warning lamp (Note 1)
Ignition switch OFF
–
For 2 seconds after turning ignition switch ON
×
(Note 2)
2 seconds later after turning ignition switch ON
×
(Note 2)
EBD function is malfunctioning.
×
BRC-84
< DTC/CIRCUIT DIAGNOSIS >
[VDC/TCS/ABS]
BRAKE WARNING LAMP
After removing/replacing an ABS actuator and electric unit (control unit), be sure to perform the following pro-
cedure.
• Adjustment of steering angle sensor neutral position: Refer to
BRC-9, "ADJUSTMENT OF STEERING
ANGLE SENSOR NEUTRAL POSITION : Description"
.
• Calibration of decel G sensor: Refer to
BRC-10, "CALIBRATION OF DECEL G SENSOR : Description"
.
>> END
VDC OFF INDICATOR LAMP
BRC-85
< DTC/CIRCUIT DIAGNOSIS >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
VDC OFF INDICATOR LAMP
Description
INFOID:0000000005517389
×
: ON –: OFF
Component Function Check
INFOID:0000000005517390
1.
VDC OFF INDICATOR LAMP OPERATION CHECK 1
Check that the lamp illuminates for approximately 2 seconds after the ignition switch is turned ON.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Proceed to diagnosis procedure. Refer to
.
2.
VDC OFF INDICATOR LAMP OPERATION CHECK 2
Check that the VDC OFF indicator lamp in the combination meter turns ON/OFF correctly when operating the
VDC OFF switch.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Check VDC OFF switch. Refer to
.
Diagnosis Procedure
INFOID:0000000005517391
1.
CHECK VDC OFF SWITCH
Check that the VDC OFF indicator lamp in the combination meter turns ON/OFF correctly when operating the
VDC OFF switch.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check VDC OFF switch. Refer to
.
2.
CHECK SELF-DIAGNOSIS
Perform self-diagnosis for “ABS” with CONSULT-III.
Is the inspection result normal?
YES
>> Check combination meter. Refer to
MWI-34, "CONSULT-III Function (METER/M&A)"
.
NO
>> Check items displayed by self-diagnosis for “ABS” with CONSULT-III.
Condition
VDC OFF indicator lamp
Ignition switch OFF
–
For 2 seconds after turning ignition switch ON
×
2 seconds later after turning ignition switch ON
–
VDC OFF switch turned ON. (VDC function is OFF.)
×
VDC/TCS function is malfunctioning.
×
ABS function is malfunctioning.
×
EBD function is malfunctioning.
×
BRC-86
< DTC/CIRCUIT DIAGNOSIS >
[VDC/TCS/ABS]
SLIP INDICATOR LAMP
SLIP INDICATOR LAMP
Description
INFOID:0000000005517393
×
: ON
: Blink –: OFF
Component Function Check
INFOID:0000000005517394
1.
CHECK SLIP INDICATOR LAMP OPERATION
Check that the lamp illuminates for approximately 2 seconds after the ignition switch is turned ON.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Proceed to diagnosis procedure. Refer to
.
Diagnosis Procedure
INFOID:0000000005517395
1.
CHECK SELF-DIAGNOSIS
Perform self-diagnosis for “ABS” with CONSULT-III.
Is the inspection result normal?
YES
>> Check combination meter. Refer to
MWI-34, "CONSULT-III Function (METER/M&A)"
.
NO
>> Check items displayed by self-diagnosis for “ABS” with CONSULT-III.
Condition
SLIP indicator lamp
Ignition switch OFF
–
For 2 seconds after turning ignition switch ON
×
2 seconds later after turning ignition switch ON
–
VDC/TCS is activated while driving.
VDC/TCS function is malfunctioning.
×
ABS function is malfunctioning.
×
EBD function is malfunctioning.
×
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст