Nissan Murano Z51. Manual — part 1198
RSU-16
< REMOVAL AND INSTALLATION >
REAR SUSPENSION ARM
REAR SUSPENSION ARM
Exploded View
INFOID:0000000005514363
NOTE:
Remove suspension arm with rear suspension member for AWD models. Refer to
.
Removal and Installation
INFOID:0000000005514364
NOTE:
Remove suspension arm with rear suspension member for AWD models. Refer to
.
REMOVAL
1.
Remove tire with power tool.
2.
Remove wheel sensor and sensor harness. Refer to
BRC-111, "REAR WHEEL SENSOR : Exploded
.
3.
Remove stabilizer connecting rod. Refer to
.
4.
Remove cotter pin of suspension arm ball joint, and loosen nut.
5.
Use the ball joint remover to remove suspension arm from axle housing. Be careful not to damage ball
joint boot.
CAUTION:
Tighten temporarily mounting nut to prevent damage to threads and to prevent ball joint remover
from coming off.
6.
Remove suspension arm.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of rear suspension member installation position (rubber bushing), under unladen
conditions with tires on level ground.
Inspection
INFOID:0000000005514365
INSPECTION AFTER REMOVAL
Appearance
Check the following items, and replace the part if necessary.
• Suspension arm and bushing for deformation, cracks or damage.
• Boot of ball joint for cracks or damage, and also for grease leakage.
1.
Suspension arm
2.
Stopper rubber
3.
Rear suspension member
Refer to
for symbols in the figure.
JPEIB0141GB
REAR SUSPENSION ARM
RSU-17
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
Ball Joint Inspection
Manually move ball stud at least ten times by hand to check for smooth movement.
Swing Torque Inspection
1.
Before measurment, move ball stud at least ten times by hand to check for smooth movement.
2.
Hook spring balance (A) at cotter pin mounting hole. Confirm
spring balance measurement value is within specifications when
ball stud begins moving.
-
If swing torque exceeds the standard range, replace suspension
arm assembly.
Axial End Play Inspection
1.
Before measurment, move ball stud at least ten times by hand to check for smooth movement.
2.
Move tip of ball stud in axial direction to check for looseness.
-
If axial end play exceeds the standard range, replace suspension arm assembly.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection. Refer to
.
2.
Check wheel alignment. Refer to
3.
Adjust neutral position of steering angle sensor. Refer to
BRC-9, "ADJUSTMENT OF STEERING ANGLE
SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
Swing torque
: Refer to
.
JPEIA0005ZZ
Axial end play
: Refer to
.
RSU-18
< UNIT REMOVAL AND INSTALLATION >
REAR SUSPENSION MEMBER
UNIT REMOVAL AND INSTALLATION
REAR SUSPENSION MEMBER
Exploded View
INFOID:0000000005514366
Removal and Installation
INFOID:0000000005514367
REMOVAL
1.
Remove tires with power tool.
2.
Remove caliper assembly. Hang caliper assembly in a place where it will not interfere with work. Refer to
BR-42, "BRAKE CALIPER ASSEMBLY : Exploded View"
CAUTION:
Avoid depressing brake pedal while caliper assembly is removed.
3.
Remove wheel sensor and sensor harness. Refer to
BRC-111, "REAR WHEEL SENSOR : Exploded
.
4.
Remove center muffler. Refer to
5.
Remove stabilizer bar. Refer to
6.
Remove drive shaft (AWD models). Refer to
.
7.
Remove propeller shaft (AWD models). Refer to
.
8.
Remove harness from rear final drive and rear suspension member (AWD models).
9.
Remove rear final drive (AWD models). Refer to
.
10. Separate the attachment between parking brake cable and vehicle and rear suspension member. Refer to
.
11. Remove rear lower link and coil spring. Refer to
12. Remove shock absorber (lower side). Refer to
13. Set suitable jack under rear suspension member.
14. Remove member stay.
15. Remove rear suspension member and rebound stopper.
16. Slowly lower jack, then remove rear suspension member, suspension arm, radius rod, front lower link and
axle from vehicle as a unit.
17. Remove suspension arm. Refer to
18. Remove radius rod. Refer to
1.
Rebound stopper
2.
Rear suspension member
3.
Member stay
Refer to
for symbols in the figure.
JPEIB0148GB
REAR SUSPENSION MEMBER
RSU-19
< UNIT REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
19. Remove front lower link. Refer to
.
INSTALLATION
Note the following, and install in the reverse order of the removal.
• Perform the final tightening of each of parts under unladen conditions, which were removed when removing
rear suspension assembly.
• Check wheel sensor harness for proper connection. Refer to
BRC-111, "REAR WHEEL SENSOR : Exploded
.
• Never reuse cotter pin.
Inspection
INFOID:0000000005514368
INSPECTION AFTER REMOVAL
Check rear suspension member for deformation, cracks, or any other damage. Replace if necessary.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection. Refer to
.
2.
Adjust parking brake operation (stroke).
PB-3, "Inspection and Adjustment"
3.
Check wheel alignment. Refer to
4.
Adjust neutral position of steering angle sensor. Refer to
BRC-9, "ADJUSTMENT OF STEERING ANGLE
SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст