Nissan Murano Z51. Manual — part 1197
RSU-12
< REMOVAL AND INSTALLATION >
RADIUS ROD
RADIUS ROD
Exploded View
INFOID:0000000005514354
Removal and Installation
INFOID:0000000005514355
REMOVAL
1.
Remove tire with power tool.
2.
Remove wheel sensor and sensor harness. Refer to
BRC-111, "REAR WHEEL SENSOR : Exploded
.
3.
Remove rear lower link and coil spring. Refer to
4.
Remove shock absorber mounting bolt (lower side) with power tool. Refer to
5.
Remove front lower link mounting bolt and nut (axle housing side) with power tool. Refer to
6.
Loosen front lower link mounting bolt and nut (suspension member side). Refer to
.
7.
Remove radius rod mounting bolts and nuts (axle housing side) with power tool.
8.
Remove radius rod mounting bolt (rear suspension member side) with power tool, then remove radius
rod.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of rear suspension member and axle installation position (rubber bushing), under
unladen conditions with tires on level ground.
Inspection
INFOID:0000000005514356
INSPECTION AFTER REMOVAL
Check radius rod and bushing for any deformation, cracks, or damage. Replace if necessary.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection. Refer to
.
1.
Upper seat
2.
Coil spring
3.
Rubber seat
4.
Rear lower link
5.
Rear suspension member
6.
Radius rod
7.
Front lower link
Refer to
for symbols in the figure.
JPEIB0146GB
RADIUS ROD
RSU-13
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
2.
Check wheel alignment. Refer to
3.
Adjust neutral position of steering angle sensor. Refer to
BRC-9, "ADJUSTMENT OF STEERING ANGLE
SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
RSU-14
< REMOVAL AND INSTALLATION >
FRONT LOWER LINK
FRONT LOWER LINK
Exploded View
INFOID:0000000005514357
Removal and Installation
INFOID:0000000005514358
REMOVAL
1.
Remove tire with power tool.
2.
Remove wheel sensor and sensor harness. Refer to
BRC-111, "REAR WHEEL SENSOR : Exploded
.
3.
Remove rear lower link and coil spring. Refer to
4.
Remove shock absorber mounting bolt (lower side) with power tool. Refer to
5.
Remove stabilizer bushing and stabilizer clamp. Refer to
.
6.
Remove front lower link mounting bolts and nuts (rear suspension member side) with power tool.
7.
Remove front lower link mounting bolts and nuts (axle housing side) with power tool.
8.
Remove front lower link.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of rear suspension member and axle installation position (rubber bushing), under
unladen conditions with tires on level ground.
Inspection
INFOID:0000000005514359
INSPECTION AFTER REMOVAL
Check front lower link and bushing for any deformation, cracks, or damage. Replace if necessary.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection. Refer to
.
2.
Check wheel alignment. Refer to
3.
Adjust neutral position of steering angle sensor. Refer to
BRC-9, "ADJUSTMENT OF STEERING ANGLE
SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
1.
Upper seat
2.
Coil spring
3.
Rubber seat
4.
Rear lower link
5.
Rear suspension member
6.
Radius rod
7.
Front lower link
Refer to
for symbols in the figure.
JPEIB0146GB
REAR STABILIZER
RSU-15
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
REAR STABILIZER
Exploded View
INFOID:0000000005514360
Removal and Installation
INFOID:0000000005514361
REMOVAL
1.
Remove tires with power tool.
2.
Remove stabilizer connecting rod mount bracket.
3.
Remove stabilizer connecting rod.
CAUTION:
Apply a matching mark to identify the installation position.
4.
Remove mounting bolts on stabilizer clamp and remove stabilizer bar with power tool.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Check the matching mark when installing.
• Tighten the mounting nut to the specified torque while holding a hexagonal part of stabilizer connecting rod
side.
Inspection
INFOID:0000000005514362
INSPECTION AFTER REMOVAL
Check stabilizer bar, stabilizer bushing, stabilizer clamp, stabilizer connecting rod, stabilizer connecting rod
mounting bracket for any deformation, crack or damage. Replace if necessary.
1.
Suspension arm
2.
Stabilizer connecting rod mount
bracket
3.
Stabilizer connecting rod
4.
Stabilizer bar
5.
Stabilizer bushing
6.
Stabilizer clamp
for symbols in the figure.
JPEIB0085GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст