Nissan Murano Z51. Manual — part 791
PREPARATION
FL-3
< PREPARATION >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000005515867
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tool
INFOID:0000000005515868
(Kent-Moore No.)
Tool name
Description
(J-46211)
Fuel tank lock ring wrench
Removing and installing fuel tank retainer
SBIA0388E
Tool name
Description
Power tool
Loosening nuts and bolts
PBIC0190E
FL-4
< PERIODIC MAINTENANCE >
FUEL SYSTEM
PERIODIC MAINTENANCE
FUEL SYSTEM
Inspection
INFOID:0000000005515869
Inspect fuel lines, fuel filler cap, and fuel tank for improper attach-
ment, leakage, cracks, damage, loose connections, chafing or dete-
rioration.
If necessary, repair or replace damaged parts.
Quick Connector
INFOID:0000000005515870
CAUTION:
• After connecting fuel tube quick connectors, check quick con-
nectors are secure.
• Ensure that connector and resin tube never contact any adja-
cent parts.
A
: Engine
B
: Fuel line
C
: Fuel tank
JPBIA0129ZZ
1
: Quick connector
2
: Retainer
A
: Hard tube (or the equivalent)
B
: Connection (cross-section)
C
: Resin tube
D
: To under floor fuel line
E
: To fuel tank
F
: Tab
G
: Disconnection
JPBIA0130ZZ
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FL-5
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
REMOVAL AND INSTALLATION
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
Exploded View
INFOID:0000000005515871
REMOVAL
DISASSEMBLY
1.
Retainer
2.
Sub fuel level sensor unit
3.
Seal packing
4.
Main fuel level sensor unit, fuel filter
and fuel pump assembly
A.
Right side
B.
Left side
: Vehicle front
Refer to
JPBIA1694GB
FL-6
< REMOVAL AND INSTALLATION >
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
Removal and Installation
INFOID:0000000005515872
WARNING:
Read “General Precautions” when working on the fuel system. Refer to
REMOVAL
1.
Check fuel level on fuel gauge. If fuel gauge indicates more than
the level as shown in the figure (full or almost full), drain fuel
from fuel tank until fuel gauge indicates level as shown in the fig-
ure or below.
NOTE:
Because fuel will be spilled when removing main and sub fuel
level sensor units for the top of the fuel is above the main and
sub fuel level sensor units installation surface.
• As a guide, fuel level becomes the position as shown in the
figure or below when approximately 20 (5-1/4 US gal, 4-3/8
Imp gal) of fuel are drained from fuel tank.
• In a case that fuel pump does not operate, perform the follow-
ing procedure.
a.
Insert hose of less than 25 mm (0.98 in) in diameter into fuel filler tube through fuel filler opening to draw
fuel from fuel filler tube.
b.
Disconnect fuel filler hose from fuel filler tube. Refer to
c.
Insert hose into fuel tank through fuel filler hose to draw fuel from fuel tank.
2.
Release the fuel pressure from the fuel lines. Refer to
3.
Open fuel filler lid.
4.
Open filler cap and release the pressure inside fuel tank.
5.
Remove rear seat cushion and reclining device assembly. Refer to
1.
Sub fuel level sensor unit
2.
Sub fuel level sensor unit base
3.
Fuel filter and fuel pump assembly
4.
Fuel level sensor unit
: Vehicle front
PBIC4901J
JPBIA1701ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст