Nissan Murano Z51. Manual — part 790

FRONT DRIVE SHAFT

FAX-53

< REMOVAL AND INSTALLATION >

[AWD]

C

E

F

G

H

I

J

K

L

M

A

B

FAX

N

O

P

b.

Secure dynamic damper with bands in the following specified
position (A) when installing.

CAUTION:

Never reuse bands.

Inspection

INFOID:0000000005518988

INSPECTION AFTER REMOVAL

• Move joint up/down, left/right, and in the axial directions. Check for motion that is not smooth and for signifi-

cant looseness.

• Check boot for cracks, damage, and leakage of grease.
• Disassemble drive shaft and exchange malfunctioning part if there

is a non-standard condition.

INSPECTION AFTER DISASSEMBLY

Shaft

Check shaft for runout, cracks, or other damage. Replace if necessary.

Dynamic Damper

Check damper for cracks or wear. Replace if necessary.

Joint Sub-Assembly (Wheel Side)

Check the following:
• Joint sub-assembly for rough rotation and excessive axial looseness.
• The inside of the joint sub-assembly for entry of foreign material.
• Joint sub-assembly for compression scars, cracks, and fractures inside of joint sub-assembly.
Replace joint sub-assembly if there are any non-standard conditions of components.

Housing Assembly (Transaxle Side)

Replace housing assembly if there is scratching or wear of housing assembly roller contact surface.

Link Shaft (Right side)

Check shaft for runout, cracks, or other damage. Replace if necessary.

Support Bearing (Right Side)

Make sure wheel bearing rolls freely and is free from noise, cracks, pitting or wear. Replace support bearing if
there are any non-standard conditions.

Support Bearing Bracket (Right Side)

Check for bending, cracks, or damage. Replace support bearing bracket if there are any non-standard condi-
tions.

A :

Refer

to

FAX-54, "Drive Shaft"

.

JPDIF0178ZZ

SDIA1190J

FAX-54

< SERVICE DATA AND SPECIFICATIONS (SDS)

[AWD]

SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)

Wheel Bearing

INFOID:0000000005518989

Drive Shaft

INFOID:0000000005518990

Item

Standard

Axial end play

0.05 mm (0.002 in) or less

Item

Left side

Right side

Grease quantity

Wheel side

170 – 190 g (6.00 – 6.70 oz)

Transaxle side

155 – 175 g (5.47 – 6.17 oz)

Boots installed length

Wheel side

158.6 mm (6.24 in)

Transaxle side

163.67 mm (6.44 in)

159.47 mm (6.28 in)

Dimension of dynamic damper

—

202 – 208 mm (7.95 – 8.19 in)

FL-1

ENGINE

C

D

E

F

G

H

I

J

K

L

M

SECTION

FL

A

FL

N

O

P

CONTENTS

FUEL SYSTEM

PRECAUTION . . . . . . . . . . . ...

2

PRECAUTIONS . . . . . . . . . . . . ...

2

General Precautions . . . . . . . . . . . .....

2

PREPARATION . . . . . . . . . . .

3

PREPARATION . . . . . . . . . . . . ...

3

Special Service Tool . . . . . . . . . . . .....

3

Commercial Service Tool . . . . . . . . . . ..

3

PERIODIC MAINTENANCE . . . . . . ..

4

FUEL SYSTEM . . . . . . . . . . . . .

4

Inspection . . . . . . . . . . . . . . . . ..

4

Quick Connector . . . . . . . . . . . . . ...

4

REMOVAL AND INSTALLATION . . . .

5

FUEL LEVEL SENSOR UNIT, FUEL FILTER
AND FUEL PUMP ASSEMBLY . . . . . . .

5

Exploded View . . . . . . . . . . . . . . ..

5

Removal and Installation . . . . . . . . . . ..

6

Disassembly and Assembly . . . . . . . . . .

10

Inspection . . . . . . . . . . . . . . . .

10

FUEL TANK . . . . . . . . . . . . . ..

12

Exploded View . . . . . . . . . . . . . . .

12

Removal and Installation . . . . . . . . . . .

12

Inspection . . . . . . . . . . . . . . . .

14

SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .

15

SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .

15

Fuel Tank . . . . . . . . . . . . . . . . .

15

FL-2

< PRECAUTION >

PRECAUTIONS

PRECAUTION

PRECAUTIONS

General Precautions

INFOID:0000000005515866

WARNING:

When replacing fuel line parts, be sure to observe the following.
• Put a “CAUTION: FLAMMABLE” sign in the workshop.
• Be sure to work in a well ventilated area and furnish workshop with a CO

2

fire extinguisher.

• Never smoke while servicing fuel system. Keep open flames and sparks away from the work area.

CAUTION:

• Use gasoline required by the regulations for octane number. Refer to

GI-28, "Fuel"

.

• Before removing fuel line parts, perform out the following procedures:
- Put drained fuel in an explosion-proof container and put the lid on securely. Keep the container in

safe area.

- Release fuel pressure from the fuel lines. Refer to

EC-530, "Inspection"

.

- Disconnect the battery cable from the negative terminal.
• Always replace O-ring and clamps with new ones.
• Never kink or twist tubes when they are being installed.
• Never tighten hose clamps excessively to avoid damaging hoses.
• After installing tubes, check there is no fuel leakage at connections in the following steps.
- Apply fuel pressure to fuel lines with turning ignition switch “ON” (with engine stopped). Then check

for fuel leakage at connections.

- Start engine and rev it up and check for fuel leakage at connections.
• Use only a genuine NISSAN fuel filler cap as a replacement. If an incorrect fuel filler cap is used, the

“MIL” may come on.

• For servicing “Evaporative Emission System” parts, refer to

EC-77, "System Diagram"

.

• For servicing “On Board Refueling Vapor Recovery (ORVR)” parts, refer to

EC-451, "Description"

.