Nissan Murano Z51. Manual — part 935
INT-10
< PRECAUTION >
PRECAUTIONS
• After finishing work, confirm that all control unit connectors are connected properly, then re-connect both
battery cables.
• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
For vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock and
cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the operation pro-
cedure below before starting the repair operation.
OPERATION PROCEDURE
1.
Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2.
Turn the push-button ignition switch to ACC position.
(At this time, the steering lock will be released.)
3.
Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
4.
Perform the necessary repair operation.
5.
When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the push-button ignition switch from ACC position to ON position, then to LOCK position. (The steering
wheel will lock when the push-button ignition switch is turned to LOCK position.)
6.
Perform self-diagnosis check of all control units using CONSULT-III.
FOR MEXICO : Precaution for Procedure without Cowl Top Cover
INFOID:0000000005716265
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.
FOR MEXICO : Precaution for Work
INFOID:0000000005716266
• After removing and installing the opening/closing parts, be sure to carry out fitting adjustments to check their
operation.
• Check the lubrication level, damage, and wear of each part. If necessary, grease or replace it.
PIIB3706J
PREPARATION
INT-11
< PREPARATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
PREPARATION
PREPARATION
Commercial Service Tools
INFOID:0000000005716277
Special Service Tools
INFOID:0000000005716278
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool name
Description
Engine ear
Locates the noise
Remover tool
Removes the clips, pawls and metal clips
Power tool
SIIA0995E
JMKIA3050ZZ
PIIB1407E
Tool number
(Kent-Moore No.)
Tool name
Description
(J-39570)
Chassis ear
Locates the noise
(J-43980)
NISSAN Squeak and Rattle
Kit
Repairs the cause of noise
SIIA0993E
SIIA0994E
INT-12
< REMOVAL AND INSTALLATION >
DOOR FINISHER
REMOVAL AND INSTALLATION
DOOR FINISHER
FRONT DOOR FINISHER
FRONT DOOR FINISHER : Exploded View
INFOID:0000000005513287
FRONT DOOR FINISHER : Removal and Installation
INFOID:0000000005513288
CAUTION:
Wrap the tip of flat-bladed screwdriver with a cloth before remove.
REMOVAL
1.
Fully open front door window.
1.
Inside handle escutcheon
2.
Step lamp
3.
Power window switch finisher
4.
Front door finisher
5.
Front door inside handle
6.
Seat memory switch finisher
7.
Front door panel
8.
Front door inside seal
9.
Armrest finisher
10. Door mirror corner cover
11. Power window switch
12. Door mirror remote control switch
: Clip
: Pawl
JMJIA1348ZZ
DOOR FINISHER
INT-13
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
2.
Remove inside handle escutcheon (1) with remover tool (A).
3.
Remove bolt (B) located behind the inside handle escutcheon
with tool (A).
4.
Pull up power window switch finisher (1) with remover tool (A) to
disengage the pawls.
5.
Disconnect power window and door mirror remote control switch harness connectors, and then remove
power window switch finisher.
6.
Remove bolt (B) located behind power window switch finisher
with tool (A).
: Pawl
JMJIA1350ZZ
JMJIA1351ZZ
: Pawl
JMJIA1352ZZ
JMJIA1353ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст