Nissan Murano Z51. Manual — part 770
EXT-14
< REMOVAL AND INSTALLATION >
FRONT BUMPER
Removal and Installation
INFOID:0000000005516269
REMOVAL
CAUTION:
Bumper fascia is made of resin. Do not apply strong force to it, and be careful to prevent contact with
oil.
1.
Fully open hood assembly.
2.
Remove front grille. Refer to
EXT-19, "Removal and Installation"
3.
Remove headlamp extension panel. Refer to
EXL-180, "Removal and Installation"
4.
Remove clips (A) of bumper fascia assembly (1) upper side.
5.
Remove fender protector fixing clips (A) (LH/RH).
6.
Remove front under cover and bumper lower finisher (LH/RH). Refer to
.
7.
Remove bumper fascia assembly fixing bolts (A).
1.
Radiator core support
2.
Grommet
3.
Bumper fascia assembly
4.
Front fog lamp RH
5.
Bumper finisher RH
6.
Head lamp extension panel RH
7.
License plate bracket
8.
Head lamp extension panel LH
9.
Front fog lamp LH
10. Bumper finisher LH
11.
Bumper lower finisher LH
12. Bumper side bracket LH
13. Bumper stay RH
14.
Bumper side bracket RH
15. J nut
16. Bumper lower molding
17.
Bumper lower finisher RH
18. Bumper stay LH
19. Bumper reinforcement
20.
Energy absorber
21. Bumper retainer assembly
JMKIA1962ZZ
JMKIA1963ZZ
JMKIA1964ZZ
FRONT BUMPER
EXT-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
8.
Remove bumper fascia assembly fixing screws (A) (LH/RH).
9.
Disconnect front fog lamp harness connector (LH/RH).
10. Pull the bumper fascia side toward the vehicle side to disengage
the fitting of bumper side bracket and bumper fascia side.
11. Remove bumper fascia assembly.
CAUTION:
When removing bumper fascia assembly, 2 workers are required so as to prevent it from dropping.
12. Remove the following parts after removing bumper fascia assembly.
• Front fog lamp assembly (LH/RH). Refer to
EXL-182, "Removal and Installation"
.
• Bumper side bracket (LH/RH)
• License plate bracket
13. Remove energy absorber.
14. Remove bumper reinforcement mounting nuts, and then remove bumper reinforcement.
15. Remove bumper stay (LH/RH) mounting bolts, and then remove bumper stay (LH/RH).
INSTALLATION
Install in the reverse order of removal.
NOTE:
After installing, perform fitting adjustment.
JMKIA1965ZZ
: Pawl
JMKIA1966ZZ
Portion
Clearance
Front bumper – Front grille
A – A
0.2 – 2.8 mm (0.008 – 0.110 in)
Front bumper – Headlamp extension panel
B – B
0.2 – 2.8 mm (0.008 – 0.110 in)
Front bumper – Headlamp
C – C
0.3 – 2.7 mm (0.012 – 0.106 in)
Front bumper – Front fender
D – D
0.0 – 0.8 mm (0.000 – 0.031 in)
EXT-16
< REMOVAL AND INSTALLATION >
REAR BUMPER
REAR BUMPER
Exploded View
INFOID:0000000005516270
Removal and Installation
INFOID:0000000005516271
REMOVAL
CAUTION:
Bumper fascia is made of resin. Never apply strong force to it, and be careful to prevent contact with
oil.
1.
Fully open back door assembly.
2.
Remove rear combination lamp (LH/RH).
1.
Rear body complete
2.
Bumper side bracket LH
3.
Bumper stay LH
4.
Grommet
5.
Bumper fascia assembly
6.
Reflex reflector LH
7.
Reflex reflector RH
8.
Bumper side bracket RH
9.
Bumper stay RH
10. Bumper reinforcement
11.
Energy absorber
JMKIA1967ZZ
REAR BUMPER
EXT-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
3.
Remove clips (A) located under rear combination lamp (LH/RH).
4.
Remove screws (B) (LH/RH).
5.
Remove rear mudguard. Refer to
EXT-26, "Removal and Installation"
6.
Remove clips (A) of bumper fascia (1) underside (LH/RH).
7.
Remove clips (A) of bumper fascia underside.
8.
Remove screws (A) of bumper fascia front end upper (LH/RH).
JMKIA1968ZZ
JMKIA2035ZZ
JMKIA1970ZZ
JMKIA1971ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст