Nissan Murano Z50 (2003 year). Manual — part 282
WT-38
TROUBLE DIAGNOSES
Revision; 2004 April
2003 Murano
Self-Diagnosis
AES000HP
DESCRIPTION
During driving, the low tire pressure warning system receives the signal transmitted from the transmitter
installed in each wheel, and gives alarms when the tire pressure becomes low. The control unit of this system
has pressure judgement and trouble diagnosis functions.
FUNCTION
When the low tire pressure warning system detects low inflation pressure or another unusual symptom, the
warning lamps in the combination meter comes on. To start the self-diagnostic results mode, ground the self-
diagnostic (check) terminal. The malfunction location is indicated by the warning lamp flashing and the buzzer
sounds.
CONSULT-II
CONSULT-II Main Function
In a diagnosis function (main function), there are “WORK SUPPORT”, “SELF-DIAGNOSTIC RESULTS”,
“DATA MONITOR”, “CAN DIAG SUPPORT MNTR”.
CONSULT-II Application to Low Tire Pressure Warning System
×
: Applicable
– : Not applicable
Self-Diagnostic Results Mode
Diagnostic test mode
Function
WORK SUPPORT
This mode enables a technician to adjust some devices faster and more accurately by following
the indications on CONSULT-II.
SELF-DIAGNOSTIC
RESULTS
Self-diagnostic results can be read and erased quickly.
DATA MONITOR
Input/Output data in the control unit can be read.
CAN DIAG SUPPORT MNTR
The results of transmit/receive diagnosis of communication can be read.
ITEM
SELF-DIAGNOSTIC RESULTS
DATA MONITOR
Front - Left transmitter
×
×
Front - Right transmitter
×
×
Rear - Left transmitter
×
×
Rear - Right transmitter
×
×
Warning lamp
—
×
Vehicle speed
×
×
Buzzer (in control unit)
—
×
CAN Communication
×
×
Diagnostic item
Diagnostic item is detected when ···
FLAT - TIRE - FL
FLAT - TIRE - FR
FLAT - TIRE - RR
FLAT - TIRE - RL
Front-left tire pressure drops to 190 kPa (1.9 kg/cm
2
, 27 psi) or less
Front-right tire pressure drops to 190 kPa (1.9 kg/cm
2
, 27 psi) or less
Rear-right tire pressure drops to 190 kPa (1.9 kg/cm
2
, 27 psi) or less
Rear-left tire pressure drops to 190 kPa (1.9 kg/cm
2
, 27 psi) or less
[NO-DATA] - FL
[NO-DATA] - FR
[NO-DATA] - RR
[NO-DATA] - RL
Data from front-left transmitter cannot be received.
Data from front-right transmitter cannot be received.
Data from rear-right transmitter cannot be received.
Data from rear-left transmitter cannot be received.
[CHECKSUM- ERR] - FL
[CHECKSUM- ERR] - FR
[CHECKSUM- ERR] - RR
[CHECKSUM- ERR] - RL
Checksum data from front-left transmitter is malfunctioning.
Checksum data from front-right transmitter is malfunctioning.
Checksum data from rear-right transmitter is malfunctioning.
Checksum data from rear-left transmitter is malfunctioning.
[PRESSDATA- ERR] - FL
[PRESSDATA- ERR] - FR
[PRESSDATA- ERR] - RR
[PRESSDATA- ERR] - RL
Air pressure data from front-left transmitter is malfunctioning.
Air pressure data from front-right transmitter is malfunctioning.
Air pressure data from rear-right transmitter is malfunctioning.
Air pressure data from rear-left transmitter is malfunctioning.
TROUBLE DIAGNOSES
WT-39
C
D
F
G
H
I
J
K
L
M
A
B
WT
Revision; 2004 April
2003 Murano
NOTE:
Before performing the self-diagnosis, be sure to register the ID. Or, the actual malfunction location may be different from that displayed
on CONSULT-II.
Data Monitor Mode
NOTE:
Before performing the self-diagnosis, be sure to register the ID. Or, the actual malfunction location may be different from that displayed
on CONSULT-II.
[CODE- ERR] - FL
[CODE- ERR] - FR
[CODE- ERR] - RR
[CODE- ERR] - RL
Function code data from front-left transmitter is malfunctioning.
Function code data from front-right transmitter is malfunctioning.
Function code data from rear-right transmitter is malfunctioning.
Function code data from rear-left transmitter is malfunctioning.
[BATT - VOLT - LOW] - FL
[BATT - VOLT - LOW] - FR
[BATT - VOLT - LOW] - RR
[BATT - VOLT - LOW] - RL
Battery voltage of front-left transmitter drops.
Battery voltage of front-right transmitter drops.
Battery voltage of rear-right transmitter drops.
Battery voltage of rear-left transmitter drops.
VHCL_SPEED_SIG_ERR
Vehicle speed signal is error.
Diagnostic item
Diagnostic item is detected when ···
MONITOR
CONDITION
SPECIFICATION
VHCL SPEED SE
Drive vehicle.
Vehicle speed (km/h or MPH)
AIR PRESS FL
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL
●
Drive vehicle for a few minutes.
Tire pressure (kPa or psi)
or
●
Ignition switch ON and activation tool
is transmitting activation signals.
ID REGST FL
ID REGST FR
ID REGST RR
ID REGST RL
Ignition switch ON
Registration ID: DONE
No registration ID: YET
WARNING LAMP
Warning lamp on: ON
Warning lamp off: OFF
BUZZER
Buzzer in Low tire pressure warning control unit on: ON
Buzzer in Low tire pressure warning control unit off: OFF
WT-40
TROUBLE DIAGNOSES
Revision; 2004 April
2003 Murano
How to Perform Trouble Diagnosis for Quick and Accurate Repair
AES000HQ
INTRODUCTION
●
Before troubleshooting, verify customer complaints.
●
If a vehicle malfunction is difficult to reproduce, harnesses, harness connectors or terminals may be mal-
functioning. Hold and shake these parts to make sure they are securely connected.
●
When using a circuit tester to measure voltage or resistance of each circuit, be careful not to expand con-
nector terminals.
WORK FLOW
Preliminary check :
Self-diagnosis :
Trouble diagnosis for symptoms :
SEIA0100E
TROUBLE DIAGNOSES
WT-41
C
D
F
G
H
I
J
K
L
M
A
B
WT
Revision; 2004 April
2003 Murano
Preliminary Check
AES000HR
BASIC INSPECTION
1.
CHECK ALL TIRES PRESSURES
●
Check all tires pressures.
OK or NG
OK
>> GO TO 2.
NG
>> Adjust tire pressure to specified value.
2.
CHECK WARNING LAMP ACTIVATION
1.
Check warning lamp activation.
2.
Does warning lamp activate for 1 seconds when ignition switch is turned “ON”.
Does warning lamp active?
YES
>> GO TO 3.
NO
>> Check fuse and combination meter.
3.
CHECK CONNECTOR
1.
Disconnect low tire pressure warning control unit harness connectors M81 and M205.
2.
Check terminals for damage or loose connection.
3.
Reconnect harness connector.
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace damaged parts.
4.
CHECK TRANSMITTER ACTIVATION TOOL
●
Check transmitter activation tool battery.
OK or NG
OK
>> Carry out self-diagnosis.
NG
>> Replace transmitter activation tool battery.
Tire pressure
: 230 kPa (2.3 kg/cm
2
, 33 psi)
WT-42
TROUBLE DIAGNOSES
Revision; 2004 April
2003 Murano
Malfunction Code/Symptom Chart
AES000HS
Code/Symptom
Malfunction part
Reference
page
15
16
17
18
Front-left tire pressure drops to 190 kPa (1.9 kg/cm
2
, 27 psi) or less
Front-right tire pressure drops to 190 kPa (1.9 kg/cm
2
, 27 psi) or less
Rear-right tire pressure drops to 190 kPa (1.9 kg/cm
2
, 27 psi) or less
Rear-left tire pressure drops to 190 kPa (1.9 kg/cm
2
, 27 psi) or less
—
21
22
23
24
Transmitter no data (front - left)
Transmitter no data (front - right)
Transmitter no data (rear - right)
Transmitter no data (rear - left)
31
32
33
34
Transmitter checksum error (front - left)
Transmitter checksum error (front - right)
Transmitter checksum error (rear - right)
Transmitter checksum error (rear - left)
35
36
37
38
Transmitter pressure data error (front - left)
Transmitter pressure data error (front - right)
Transmitter pressure data error (rear - right)
Transmitter pressure data error (rear - left)
41
42
43
44
Transmitter function code error (front - left)
Transmitter function code error (front - right)
Transmitter function code error (rear - right)
Transmitter function code error (rear - left)
45
46
47
48
Transmitter battery voltage low (front - left)
Transmitter battery voltage low (front - right)
Transmitter battery voltage low (rear - right)
Transmitter battery voltage low (rear - left)
52
Vehicle speed signal
Warning lamp does not come on when
ignition switch is turned on.
Fuse or unified meter and A/C amp.
Low tire pressure warning control unit connector or circuit
Low tire pressure warning control unit
Warning lamp stays on when ignition
switch is turned on.
Fuse or unified meter and A/C amp.
Low tire pressure warning control unit connector or circuit
Low tire pressure warning control unit
Warning lamp blinks when ignition
switch is turned on.
Low tire pressure warning control unit harness connector or circuit
Low tire pressure warning control unit
Transmitter's mode off
ID registration not yet
Hazard warning lamp blinks when igni-
tion switch is turned on.
Low tire pressure warning control unit harness connector or circuit
Low tire pressure warning control unit
“TIRE PRESSURE” information in dis-
play does not exist.
Fuse
Display unit
Low tire pressure warning control unit
ID registration can not be completed.
Transmitter
Antenna harness connector or circuit
Antenna
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
WT-43
C
D
F
G
H
I
J
K
L
M
A
B
WT
Revision; 2004 April
2003 Murano
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
PFP:00000
Inspection 1: Transmitter or Low Tire Pressure Warning Control Unit
AES000HT
MALFUNCTION CODE NO. 21, 22, 23 OR 24
1.
CHECK CONTROL UNIT
●
Drive for several minutes. Check all tires' pressure with CONSULT-II “DATA MONITOR ITEM”.
Are all tires' pressure displayed 0 kPa?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
CHECK ANTENNA CONNECTOR
●
Check antenna and feeder connector M205 for damage or loose connections.
OK or NG
OK
>> Replace control unit, then GO TO 3.
NG
>> Repair or replace antenna or feeder connector.
3.
ID REGISTRATION
●
Carry out ID registration of all transmitters.
Is there a tire that cannot register ID?
YES
>> Replace transmitter of the tire, then GO TO 5.
NO
>> GO TO 4.
4.
VEHICLE DRIVING
●
Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
Check all tires' pressure with CONSULT-II “DATA MONITOR ITEM” within 15 minutes after vehicle speed
becomes 17 km/h (11 MPH).
Does “DATA MONITOR ITEM” displayed tire pressure as normal without any warning lamp?
YES
>> INSPECTION END.
NO
>> GO TO 5.
5.
ID REGISTRATION AND VEHICLE DRIVING
1.
Carry out ID registration of all transmitters.
2.
Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for
10 minutes. Then check all tires' pressure with CONSULT-II “DATA MONITOR ITEM” within 5 minutes.
Does “DATA MONITOR ITEM” displayed tire pressure as normal without any warning lamp?
YES
>> INSPECTION END.
NO
>> GO TO the inspection applicable to DTC.
Inspection 2: Transmitter - 1
AES000HU
MALFUNCTION CODE NO. 31, 32, 33, 34, 41, 42, 43, 44, 45, 46, 47 OR 48
1.
ID REGISTRATION (CORRECTION OF TRANSMITTER LOCATION)
1.
Carry out ID registration of all transmitters.
2.
Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for
10 minutes.
>> GO TO 2.
WT-44
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
Revision; 2004 April
2003 Murano
2.
REPLACE TRANSMITTER
1.
Check warning lamp for blink again, replace malfunctioning transmitter.
2.
Carry out ID registration of all transmitter.
Can ID registration of all transmitters be completed?
YES
>> GO TO 3.
NO
>> GO TO the inspection 1.
3.
VEHICLE DRIVING
●
Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for
10 minutes. Then check all tires' pressure with CONSULT-II “DATA MONITOR ITEM” within 5 minutes.
Does “DATA MONITOR ITEM” displayed tire pressure as normal without any warning lamp?
YES
>> INSPECTION END.
NO
>> Replace malfunctioning transmitter, and perform “Step 3” again.
Inspection 3: Transmitter - 2
AES000NF
MALFUNCTION CODE NO. 35, 36, 37 OR 38
1.
CHECK ALL TIRE PRESSURE
●
Check all tire pressures.
Are there any tires' which pressure is “64 psi” or more?
YES
>> Adjust tire pressure to specified value.
NO
>> GO TO 2.
2.
VEHICLE DRIVING
1.
Carry out ID registration of all transmitters.
2.
Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
Check all tires' pressure with CONSULT-II “DATA MONITOR ITEM” within 15 minutes after vehicle speed
become 17 km/h (11 MPH).
>> Replace transmitter with new one if “DATA MONITOR ITEM” displayed 64 psi or more. Then GO
TO 3.
3.
ID REGISTRATION AND VEHICLE DRIVING
●
Carry out ID registration of all transmitters.
●
Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for
10 minutes. Then check all tires' pressure with CONSULT-II “DATA MONITOR ITEM” within 5 minutes.
Does “DATA MONITOR ITEM” displayed tire pressure as normal without any warning lamp?
YES
>> INSPECTION END.
NO
>> GO TO the inspection applicable to DTC.
Tire pressure
: 230 kPa (2.3 kg/m
2
, 33 psi)
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
WT-45
C
D
F
G
H
I
J
K
L
M
A
B
WT
Revision; 2004 April
2003 Murano
Inspection 4: Vehicle Speed Signal
AES000HV
MALFUNCTION CODE NO. 52
1.
SELF-DIAGNOSIS RESULT CHECK
1.
Connect CONSULT-II and CONSULT-II CONVERTER to data link connector.
NOTE:
If “AIR PRESSURE MONITOR” is not indicated, go to
GI-38, "CONSULT-II Data Link Connector (DLC)
.
2.
Select “AIR PRESSURE MONITOR” on “SELECT SYSTEM” screen.
3.
Select “SELF-DIAG RESULTS” on “SELECT DIAG MODE” screen.
4.
Check display contents in self-diagnostic results.
Is “CAN COMM CIRCUIT” displayed in the self-diagnosis display items?
YES
>> Malfunction in CAN communication system. GO TO
LAN-10, "Precautions When Using CON-
.
NO
>> GO TO 2.
2.
CHECK UNIFIED METER AND A/C AMP. POWER SUPPLY CIRCUIT
1.
Disconnect unified meter and A/C amp. connector M50.
2.
Check voltage between unified meter and A/C amp. harness connector M50 terminals 21 (Y/R), 22 (G)
and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Check unified meter and A/C amp. power supply circuit
for open or short.
3.
CHECK UNIFIED METER AND A/C AMP. GROUND CIRCUIT
●
Check continuity between unified meter and A/C amp. harness connector M50 terminals 29 (B), 30 (B)
and ground.
OK or NG
OK
>> Check unified meter and A/C amp. self-diagnostic. Refer
to
NG
>> Repair or replace unified meter and A/C amp. ground circuit.
Terminals
Voltage
(Approx.)
(+)
(–)
Connector
Terminal
(Wire color)
Ground
12 V
M50
21 (Y/R)
22 (G)
SEIA0299E
Terminals
Continuity
(+)
(–)
Connector
Terminal
(Wire color)
Ground
Yes
M50
29 (B)
30 (B)
SEIA0300E
WT-46
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision; 2004 April
2003 Murano
TROUBLE DIAGNOSIS FOR SYMPTOMS
PFP:00007
Inspection 1: Warning Lamp Does Not Come On When Ignition Switch Is Turned
On.
AES000HW
DIAGNOSTIC PROCEDURE
1.
SELF-DIAGNOSIS RESULT CHECK
1.
Connect CONSULT-II and CONSULT-II CONVERTER to data link connector.
NOTE:
If “AIR PRESSURE MONITOR” is not indicated, go to
GI-38, "CONSULT-II Data Link Connector (DLC)
2.
Select “AIR PRESSURE MONITOR” on “SELECT SYSTEM” screen.
3.
Select “SELF-DIAG RESULTS” on “SELECT DIAG MODE” screen.
4.
Check display contents in self-diagnostic results.
Is “CAN COMM CIRCUIT” displayed in the self-diagnosis display items?
YES
>> Malfunction in CAN communication system. GO TO
LAN-10, "Precautions When Using CON-
NO
>> GO TO 2.
2.
CHECK COMBINATION METER
●
Check combination meter operation.
Inspection results OK?
OK
>> GO TO 3.
NG
>> Check combination meter. Refer to
3.
CHECK WARNING LAMP
●
Disconnect low tire pressure warning control unit connector.
Does the warning lamp activate?
YES
>> Replace low tire pressure warning control unit.
NO
>> GO TO 4.
4.
CHECK UNIFIED METER AND A/C AMP. POWER SUPPLY CIRCUIT
1.
Disconnect unified meter and A/C amp. connector M50.
2.
Check voltage between unified meter and A/C amp. harness connector M50 terminals 21 (Y/R), 22 (G)
and ground.
OK or NG
OK
>> GO TO 5.
NG
>> Check unified meter and A/C amp. power supply circuit
for open or short.
Terminals
Voltage
(Approx.)
(+)
(–)
Connector
Terminal
(Wire color)
Ground
12 V
M50
21 (Y/R)
22 (G)
SEIA0299E
TROUBLE DIAGNOSIS FOR SYMPTOMS
WT-47
C
D
F
G
H
I
J
K
L
M
A
B
WT
Revision; 2004 April
2003 Murano
5.
CHECK UNIFIED METER AND A/C AMP. GROUND CIRCUIT
●
Check continuity between unified meter and A/C amp. connector M50 terminals 29(B), 30(B) and ground.
OK or NG
OK
>> Check unified meter and A/C amp. Refer to
.
NG
>> Repair or replace unified meter and A/C amp. ground circuit.
Inspection 2: Warning Lamp Stays On When Ignition Switch Is Turned On.
AES000HX
DIAGNOSTIC PROCEDURE
1.
CHECK CONNECTOR
1.
Disconnect low tire pressure warning control unit connectors M81 and M205.
2.
Check terminals for damage or loose connections.
Inspection results OK?
OK
>> GO TO 2.
NG
>> Repair or replace damaged parts.
2.
CHECK POWER SUPPLY CIRCUIT 1
Check voltage between low tire pressure warning control unit connector M81 terminal 12 (R/W) and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Check low tire pressure warning control unit power sup-
ply circuit for open or short.
Terminals
Continuity
(+)
(–)
Connector
Terminal
(Wire color)
Ground
Yes
M50
29 (B)
30 (B)
SEIA0300E
Terminals
Voltage
(Approx.)
(+)
(–)
Connector
Terminal
(Wire color)
Ground
12 V
M81
12 (Y/R)
SEIA0301E
WT-48
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision; 2004 April
2003 Murano
3.
CHECK POWER SUPPLY CIRCUIT 2
1.
Turn ignition switch ON.
2.
Check voltage between low tire pressure warning control unit connector M81 terminals 11 (P/B), 24 (G)
and ground.
OK or NG
OK
>> GO TO 4.
NG
>> Check low tire pressure warning control unit power sup-
ply circuit for open or short.
4.
CHECK GROUND CIRCUIT
●
Check continuity between low tire pressure warning control unit connector M81 terminal 20(B) and
ground.
OK or NG
OK
>> Replace low tire pressure warning control unit.
NG
>> Repair or replace low tire pressure warning control unit
ground circuit.
Terminals
Voltage
(Approx.)
(+)
(–)
Connector
Terminal
(Wire color)
Ground
12 V
M81
11 (P/B)
24 (G)
SEIA0302E
Terminals
Continuity
(+)
(–)
Connector
Terminal
(Wire color)
Ground
Yes
M81
20 (B)
SEIA0303E
TROUBLE DIAGNOSIS FOR SYMPTOMS
WT-49
C
D
F
G
H
I
J
K
L
M
A
B
WT
Revision; 2004 April
2003 Murano
Inspection 3: Warning Lamp Blinks When Ignition Switch Is Turned On.
AES000HY
NOTE:
If warning lamp blink below, the system is normal.
Blink Mode A
●
This mode shows transmitter status is OFF-mode.
Carry out transmitter wake up operation. Refer to
"Transmitter Wake Up Operation"
DIAGNOSTIC PROCEDURE
1.
CHECK CONNECTOR
1.
Disconnect low tire pressure warning control unit connectors M81 and M205.
2.
Check terminals for damage or loose connections.
Inspection results OK?
OK
>> GO TO 2.
NG
>> Repair or replace damaged parts.
2.
CHECK TIRE PRESSURE WARNING CHECK CONNECTOR CIRCUIT
1.
Disconnect low tire pressure warning control unit connector M81.
2.
Check continuity between low tire pressure warning control unit harness connector M81 terminal 8 (G/W)
and ground.
OK or NG
OK
>> Replace low tire pressure warning control unit.
NG
>> Repair or replace harness connector.
SEIA0347E
Terminals
Continuity
(+)
(–)
Connector
Terminal
(Wire color)
Ground
No
M81
8 (G/W)
SEIA0304E
WT-50
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision; 2004 April
2003 Murano
Inspection 4: Hazard Warning Lamp Blinks When Ignition Switch Is Turned On.
AES000HZ
DIAGNOSTIC PROCEDURE
1.
CHECK GROUND CIRCUIT
1.
Disconnect low tire pressure waning control unit connector M81.
2.
Check continuity between low tire pressure warning control unit harness connector M81 terminal 20 (B)
and ground.
OK or NG
OK
>> Replace low tire pressure warning control unit.
NG
>> Repair or replace low tire pressure warning control unit
ground circuit.
Terminals
Continuity
(+)
(–)
Connector
Terminal
(Wire color)
Ground
Yes
M81
20 (B)
SEIA0303E
TROUBLE DIAGNOSIS FOR SYMPTOMS
WT-51
C
D
F
G
H
I
J
K
L
M
A
B
WT
Revision; 2004 April
2003 Murano
Inspection 5: “TIRE PRESSURE” Information In Display Unit Does Not Exist.
AES000I0
DIAGNOSTIC PROCEDURE
1.
SELF-DIAGNOSIS RESULT CHECK
1.
Connect CONSULT-II and CONSULT-II CONVERTER to data link connector.
NOTE:
If “AIR PRESSURE MONITOR” is not indicated, go to
GI-38, "CONSULT-II Data Link Connector (DLC)
.
2.
Select “AIR PRESSURE MONITOR” on “SELECT SYSTEM” screen.
3.
Select “SELF-DIAG RESULTS” on “SELECT DIAG MODE” screen.
4.
Check display contents in self-diagnostic results.
Is “CAN COMM CIRCUIT” displayed in the self-diagnosis display items?
YES
>> Malfunction in CAN communication system. GO TO
LAN-10, "Precautions When Using CON-
.
NO
>> GO TO 2.
2.
CHECK DISPLAY UNIT
●
Perform display unit self-diagnosis. Refer to
AV-174, "Self-Diagnosis Mode (DCU)"
.
Inspection results OK?
OK
>> Replace low tire pressure warning control unit.
NG
>> Repair or replace malfunctioning parts.
Inspection 6: ID Registration Can not Be Completed
AES000JH
DIAGNOSTIC PROCEDURE
1.
ID REGISTRATION (ALL)
●
Carry out ID registration of all transmitters.
●
Can ID registration of all transmitters be completed?
YES or NO
YES
>> INSPECTION END.
NO
WT-43, "Inspection 1: Transmitter or Low Tire Pressure Warning Control Unit"
WT-52
REMOVAL AND INSTALLATION
Revision; 2004 April
2003 Murano
REMOVAL AND INSTALLATION
PFP:00000
Transmitter
AES000I3
REMOVAL
1.
Deflate tire. Unscrew transmitter retaining nut and allow transmitter to fall into tire.
2.
Gently bounce tire so that transmitter falls to bottom of tire.
Place on tire changing machine and break both tire beads
ensuring that the transmitter remains at the bottom of the tire.
3.
Turn tire so that valve hole is at bottom and bounce so that
transmitter is near valve hole. Carefully lift tire onto turntable and
position valve hole (and transmitter) 270 degree from mounting/
dismounting head.
4.
Lubricate tire well and remove first side of the tire. Reach inside
the tire and remove the transmitter. Remove second side of tire.
INSTALLATION
1.
Put first side of tire onto rim.
2.
Mount transmitter on rim and tighten nut.
SEIA0047E
SEIA0048E
SEIA0049E
SEIA0203E
REMOVAL AND INSTALLATION
WT-53
C
D
F
G
H
I
J
K
L
M
A
B
WT
Revision; 2004 April
2003 Murano
3.
Place wheel on turntable of tire machine. Ensure that transmitter
is 270 degree from mounting head when second side of tire is
fitted.
NOTE:
Do not touch transmitter at mounting head.
4.
Lubricate tire well and fit second side of tire as normal. Ensure that tire does not rotate relative to rim.
5.
Inflate tire and fit to appropriate wheel position.
SEIA0048E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст