Nissan Pathfinder (2007 year). Manual — part 98
VEHICLE SECURITY (THEFT WARNING) SYSTEM
BL-77
C
D
E
F
G
H
J
K
L
M
A
B
BL
2007 Pathfinder
Symptom Chart
EIS007PU
*1: Make sure the system is in the armed phase.
PROCEDURE
Diagnostic procedure
SYMPTOM
1
Vehicle security
system cannot be
set by ····
AII items
Diagnostic Procedure 1
Refer to
BL-78, "Diagnostic Procedure 1"
If the above systems are “OK”, replace BCM. Refer to
Lock/unlock switch
Diagnostic Procedure 6
Refer to
BL-83, "Diagnostic Procedure 6"
If the above systems are “OK”, check main power window and door lock/
unlock switch.
Door outside key
Diagnostic Procedure 3
Refer to
BL-81, "Diagnostic Procedure 3"
If the above systems are “OK”, check main power window and door lock/
unlock switch.
Security indicator does not turn “ON”.
Diagnostic Procedure 2
Refer to
BL-80, "Diagnostic Procedure 2"
If the above systems are “OK”, replace BCM. Refer to
2
*1 Vehicle secu-
rity system does
not alarm when
····
Any door or glass hatch is
opened.
Diagnostic Procedure 1
Refer to
BL-78, "Diagnostic Procedure 1"
If the above systems are “OK”, replace BCM. Refer to
3
Vehicle security
alarm does not
activate.
Horn alarm
Diagnostic Procedure 4
Refer to
BL-83, "Diagnostic Procedure 4"
If the above systems are “OK”, check horn system.
Refer to
.
Headlamp alarm
Diagnostic Procedure 5
Refer to
BL-83, "Diagnostic Procedure 5"
If the above systems are “OK”, replace BCM. Refer to
4
Vehicle security
system cannot be
canceled by ····
Door outside key
Diagnostic Procedure 3
Refer to
BL-81, "Diagnostic Procedure 3"
If the above systems are “OK”, check main power window and door lock/
unlock switch.
Keyfob
Check remote keyless entry function.
If the above systems are “OK”, replace BCM. Refer to
BL-78
VEHICLE SECURITY (THEFT WARNING) SYSTEM
2007 Pathfinder
Diagnostic Procedure 1
EIS007PV
DOOR SWITCH AND GLASS HATCH AJAR SWITCH CHECK
1.
CHECK DOOR SWITCHES INPUT SIGNAL
With CONSULT-II
Check door switches ("DOOR SW-DR", "DOOR SW-AS", "DOOR SW-RL", "DOOR SW-RR", "BACK DOOR
SW", "TRNK OPN MNTR") in DATA MONITOR mode with CONSULT–II. Refer to
.
●
When glass hatch or doors are open:
●
When glass hatch or doors are closed:
Without CONSULT-II
Check voltage between BCM connector M18 or M19 terminals 12, 13, 42, 43, 47, 48 and ground.
OK or NG
OK
>> Door switch circuit is OK.
NG
>> GO TO 2.
DOOR SW-DR
: ON
DOOR SW-AS
: ON
DOOR SW-RL
: ON
DOOR SW-RR
: ON
BACK DOOR SW
: ON
TRNK OPN MNTR
: ON
DOOR SW-DR
: OFF
DOOR SW-AS
: OFF
DOOR SW-RL
: OFF
DOOR SW-RR
: OFF
BACK DOOR SW
: OFF
TRNK OPN MNTR
: OFF
WIIA0466E
Connec-
tor
Item
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(–)
M19
Glass hatch
ajar switch
42
Ground
Open
↓
Closed
0
→
5
Back door
switch
43
0
↓
Battery voltage
Front door
switch LH
47
Rear door
switch LH
48
M18
Front door
switch RH
12
Rear door
switch RH
13
WIIA0444E
VEHICLE SECURITY (THEFT WARNING) SYSTEM
BL-79
C
D
E
F
G
H
J
K
L
M
A
B
BL
2007 Pathfinder
2.
CHECK DOOR AND GLASS HATCH AJAR SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect door switch, glass hatch ajar switch and BCM.
3.
Check continuity between door switch connector (B) B8 (Front LH), B108 (Front RH), B18 (Rear LH),
B116 (Rear RH) terminal 2 or back door switch connector (C) D502 terminal 3 or glass hatch ajar switch
connector (D) D503 terminal 1 and BCM connector (A) M18, M19 terminals 12, 13, 42, 43, 47 and 48.
4.
Check continuity between door switch connector (B) B8 (Front
LH), B108 (Front RH), B18 (Rear LH), B116 (Rear RH) terminal
2 or back door switch connector (C) D502 terminal 3 or glass
hatch ajar switch connector (D) D503 terminal 1 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness.
3.
CHECK DOOR AND GLASS HATCH AJAR SWITCHES
Check continuity between front/rear door switch connector (A) terminal 2 or back door switch connector (B)
terminal 3 or glass hatch ajar switch connector (C) terminal 1 and ground.
OK or NG
OK
>> Check switch case ground condition (front and rear door
and glass hatch) or ground circuit (back door).
NG
>> Replace door or glass hatch ajar switch.
1 - 42
: Continuity should exist.
2 - 47
: Continuity should exist.
2 - 12
: Continuity should exist.
2 - 48
: Continuity should exist.
2 - 13
: Continuity should exist.
3 - 43
: Continuity should exist.
1 - Ground
: Continuity should not exist.
2 - Ground
: Continuity should not exist.
3 - Ground
: Continuity should not exist.
WIIA0738E
Switch
Terminals
Condition
Continuity
A: Door switch
(front and rear)
2 – Ground
Open
Yes
Closed
No
B: Back door switch
1 – 3
Open
Yes
Closed
No
C: Glass hatch ajar
switch
1 – Ground
Open
Yes
Closed
No
WIIA0739E
BL-80
VEHICLE SECURITY (THEFT WARNING) SYSTEM
2007 Pathfinder
Diagnostic Procedure 2
EIS007PW
SECURITY INDICATOR LAMP CHECK
1.
SECURITY INDICATOR LAMP ACTIVE TEST
With CONSULT-II
Check "THEFT IND” in "ACTIVE TEST" mode with CONSULT-II.
Without CONSULT-II
1.
Turn ignition switch OFF.
2.
Check voltage between BCM harness connector M18 terminal
23 and ground.
OK or NG
OK
>> Security indicator lamp is OK.
NG
>> GO TO 2.
2.
SECURITY INDICATOR LAMP CHECK
Check security indicator lamp condition. Refer to
DI-11, "SELF-DIAGNOSIS FUNCTION"
.
OK or NG
OK
>> GO TO 3.
NG
>> Replace combination meter. Refer to
.
LIIA0044E
Connector
Terminal
Security indi-
cator lamp
condition
Voltage (V)
(Approx.)
(+)
(-)
M18
23
Ground
Illuminated
0
Not illumi-
nated
Battery volt-
age
PIIA6230E
VEHICLE SECURITY (THEFT WARNING) SYSTEM
BL-81
C
D
E
F
G
H
J
K
L
M
A
B
BL
2007 Pathfinder
3.
CHECK HARNESS CONTINUITY
1.
Turn ignition switch OFF.
2.
Disconnect BCM and combination meter connector.
3.
Check continuity between BCM connector M18 terminal 23 and
combination meter harness connector M24 terminal 39.
4.
Check continuity between BCM connector M18 terminal 23 and
ground.
OK or NG
OK
>> Check the following:
●
10A fuse [No. 19, located in fuse block (J/B)]
●
Harness for open or short between combination meter and fuse
NG
>> Repair or replace harness.
Diagnostic Procedure 3
EIS007PX
1.
CHECK DOOR KEY CYLINDER SWITCH LH
With CONSULT-II
Check front door lock assembly LH (key cylinder switch) ("KEY CYL LK-SW") and ("KEY CYL UN-SW) in
DATA MONITOR mode with CONSULT–II. Refer to
.
●
When key inserted in left front key cylinder is turned to LOCK:
●
When key inserted in left front key cylinder is turned to
UNLOCK:
Without CONSULT-II
Check voltage between main power window and door lock/unlock
switch connector D7 terminals 4, 6 and ground.
OK or NG
OK
>> Key cylinder switch signal is OK.
NG
>> GO TO 2.
23 - 39
: Continuity should exist.
23 - Ground
: Continuity should not exist.
WIIA0461E
KEY CYL LK-SW
: ON
KEY CYL UN-SW
: ON
LIIA0188E
Connector
Terminals
Condition of left front key cylinder
Voltage (V)
(Approx.)
(+)
(–)
D7
4
Ground
Neutral/Unlock
5
Lock
0
6
Neutral/Lock
5
Unlock
0
LIIA0566E
BL-82
VEHICLE SECURITY (THEFT WARNING) SYSTEM
2007 Pathfinder
2.
CHECK DOOR KEY CYLINDER SWITCH LH GROUND HARNESS
1.
Turn ignition switch OFF.
2.
Disconnect front door lock assembly LH (key cylinder switch).
3.
Check continuity between front door lock assembly LH (key cyl-
inder switch) connector D14 terminal 4 and body ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness.
3.
CHECK FRONT DOOR LOCK ASSEMBLY LH (KEY CYLINDER SWITCH)
Check continuity between front door lock assembly LH (key cylinder
switch) terminals 3, 4 and 5.
OK or NG
OK
>> GO TO 4.
NG
>> Replace front door lock assembly LH (key cylinder switch). Refer to
.
4.
CHECK DOOR KEY CYLINDER HARNESS
Check continuity between main power window and door lock/unlock
switch connector (A) D7 terminals 4, 6 and front door lock assembly
LH (key cylinder switch) connector (B) D14 terminals 3, 5 and body
ground.
OK or NG
OK
>> Replace main power window and door lock/unlock switch.
NG
>> Repair or replace harness.
Connector
Terminals
Continuity
D14
4 – Ground
Yes
WIIA0677E
Terminals
Condition
Continuity
4 – 5
Key is turned to LOCK.
Yes
Key is in N position or turned to
UNLOCK
No
3 – 4
Key is turned to UNLOCK.
Yes
Key is in N position or turned to LOCK
No
WIIA0458E
Connector
Terminals
Connector
Terminals
Continuity
A: Main
power win-
dow and
door lock/
unlock
switch
4
B: Front
door lock
assembly
LH (key
cylinder
switch)
5
Yes
6
3
Yes
4, 6
Ground
No
WIIA1313E
VEHICLE SECURITY (THEFT WARNING) SYSTEM
BL-83
C
D
E
F
G
H
J
K
L
M
A
B
BL
2007 Pathfinder
Diagnostic Procedure 4
EIS007PY
VEHICLE SECURITY HORN ALARM CHECK
1.
CHECK HORN OPERATION
Check if horn sounds with horn switch.
Does horn operate?
Yes
>> Check harness for open or short between IPDM E/R and horn relay.
No
>> Check horn circuit. Refer to
Diagnostic Procedure 5
EIS007PZ
VEHICLE SECURITY HEADLAMP ALARM CHECK
1.
CHECK VEHICLE SECURITY HEADLAMP ALARM OPERATION
Check if headlamps operate with lighting switch.
Do headlamps come on when turning switch ON?
Yes
>> Headlamp alarm is OK.
No
>> Check headlamp system. Refer to
.
Diagnostic Procedure 6
EIS007Q0
DOOR LOCK/UNLOCK SWITCH CHECK
1.
CHECK DOOR LOCK/UNLOCK SWITCH INPUT SIGNAL
Check if power door lock operates with door lock/unlock switch.
Do doors lock/unlock when using each door lock/unlock switch?
Yes
>> Door lock/unlock switch is OK.
No
>> Refer to
BL-30, "Door Lock/Unlock Switch Check"
.
BL-84
DOOR
2007 Pathfinder
DOOR
PFP:80100
Fitting Adjustment
EIS007Q1
FRONT DOOR
Longitudinal clearance and surface height adjustment at front end
1.
2.
Loosen the hinge bolts. Raise or lower the front door at rear end to adjust.
3.
Install the fender. Refer to
REAR DOOR
Longitudinal clearance and surface height adjustment at front end
1.
Remove the center pillar upper finisher. Refer to
2.
Loosen the lower hinge bolts.
3.
From inside the vehicle, loosen the upper hinge nuts. Open the door, and raise or lower the rear end of the
door to adjust.
4.
Install the center pillar lower finisher. Refer to
A.
4.5
±
1.0 mm (0.177
±
0.039 in)
WIIA0732E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст