Nissan Pathfinder (2007 year). Manual — part 215
DTC P2127, P2128 APP SENSOR
EC-587
C
D
E
F
G
H
I
J
K
L
M
A
EC
2007 Pathfinder
Wiring Diagram
UBS00KHB
BBWA1748E
EC-588
DTC P2127, P2128 APP SENSOR
2007 Pathfinder
Specification data are reference values and are measured between each terminal and ground.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
Diagnostic Procedure
UBS00KHC
1.
CHECK GROUND CONNECTIONS
1.
Turn ignition switch OFF.
2.
Loosen and retighten three ground screws on the body, Refer to
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace ground connections.
TER-
MINAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA (DC Voltage)
47
L
Sensor power supply
(Throttle position sensor)
[Ignition switch: ON]
Approximately 5V
82
B
Sensor ground
(APP sensor 1)
[Engine is running]
●
Warm-up condition
●
Idle speed
Approximately 0V
83
GR
Sensor ground
(APP sensor 2)
[Engine is running]
●
Warm-up condition
●
Idle speed
Approximately 0V
90
L
Sensor power supply
(APP sensor 1)
[Ignition switch: ON]
Approximately 5V
91
G
Sensor power supply
(APP sensor 2)
[Ignition switch: ON]
Approximately 5V
98
GR
Accelerator pedal position
sensor 2
[Ignition switch: ON]
●
Engine: Stopped
●
Accelerator pedal: Fully released
0.28 - 0.48V
[Ignition switch: ON]
●
Engine: Stopped
●
Accelerator pedal: Fully depressed
More than 2.0V
106
R
Accelerator pedal position
sensor 1
[Ignition switch: ON]
●
Engine: Stopped
●
Accelerator pedal: Fully released
0.65 - 0.87V
[Ignition switch: ON]
●
Engine: Stopped
●
Accelerator pedal: Fully depressed
More than 4.3V
BBIA0539E
DTC P2127, P2128 APP SENSOR
EC-589
C
D
E
F
G
H
I
J
K
L
M
A
EC
2007 Pathfinder
2.
CHECK APP SENSOR 2 POWER SUPPLY CIRCUIT-I
1.
Disconnect accelerator pedal position (APP) sensor harness connector.
2.
Turn ignition switch ON.
3.
Check voltage between APP sensor terminal 1 and ground with
CONSULT-II or tester.
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 3.
3.
CHECK APP SENSOR 2 POWER SUPPLY CIRCUIT-II
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check harness continuity between APP sensor terminal 1 and ECM terminal 91.
Refer to wiring diagram.
OK or NG
OK
>> GO TO 4.
NG
>> Repair open circuit.
4.
CHECK THROTTLE POSITION SENSOR 2 POWER SUPPLY CIRCUIT-III
Check harness for short to power and short to ground, between the following terminals.
OK or NG
OK
>> GO TO 5.
NG
>> Repair short to ground or short to power in harness or connectors.
5.
CHECK THROTTLE POSITION SENSOR
Refer to
EC-341, "Component Inspection"
OK or NG
OK
>> GO TO 11.
NG
>> GO TO 6.
Voltage: Approximately 5V
BBIA0556E
PBIB2611E
Continuity should exist.
ECM terminal
Sensor terminal
Reference Wiring Diagram
91
APP sensor terminal 1
47
Electric throttle control actuator terminal 2
EC-590
DTC P2127, P2128 APP SENSOR
2007 Pathfinder
6.
REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR
1.
Replace electric throttle control actuator.
2.
Perform
EC-77, "Throttle Valve Closed Position Learning"
.
3.
Perform
EC-77, "Idle Air Volume Learning"
>> INSPECTION END
7.
CHECK APP SENSOR 2 GROUND CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check harness continuity between APP sensor terminal 5 and ECM terminal 83.
Refer to Wiring Diagram.
4.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 8.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
8.
CHECK APP SENSOR 2 INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Check harness continuity between ECM terminal 98 and APP sensor terminal 6.
Refer to Wiring Diagram.
2.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 9.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
9.
CHECK APP SENSOR
Refer to
EC-591, "Component Inspection"
OK or NG
OK
>> GO TO 11.
NG
>> GO TO 10.
10.
REPLACE ACCELERATOR PEDAL ASSEMBLY
1.
Replace accelerator pedal assembly.
2.
Perform
EC-77, "Accelerator Pedal Released Position Learning"
3.
Perform
EC-77, "Throttle Valve Closed Position Learning"
.
4.
Perform
EC-77, "Idle Air Volume Learning"
>> INSPECTION END
11.
CHECK INTERMITTENT INCIDENT
Refer to
EC-145, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
.
>> INSPECTION END
Continuity should exist.
Continuity should exist.
DTC P2127, P2128 APP SENSOR
EC-591
C
D
E
F
G
H
I
J
K
L
M
A
EC
2007 Pathfinder
Component Inspection
UBS00KHD
ACCELERATOR PEDAL POSITION SENSOR
1.
Reconnect all harness connectors disconnected.
2.
Turn ignition switch ON.
3.
Check voltage between ECM terminals 106 (APP sensor 1 sig-
nal), 98 (APP sensor 2 signal) and ground under the following
conditions.
4.
If NG, replace accelerator pedal assembly and go to next step.
5.
Perform
EC-77, "Accelerator Pedal Released Position Learning"
6.
Perform
EC-77, "Throttle Valve Closed Position Learning"
.
7.
Perform
EC-77, "Idle Air Volume Learning"
.
Removal and Installation
UBS00KHE
ACCELERATOR PEDAL
Refer to
ACC-3, "ACCELERATOR CONTROL SYSTEM"
Terminal
Accelerator pedal
Voltage
106
(Accelerator pedal position
sensor 1)
Fully released
0.65 - 0.87V
Fully depressed
More than 4.3V
98
(Accelerator pedal position
sensor 2)
Fully released
0.28 - 0.48V
Fully depressed
More than 2.0V
MBIB0023E
EC-592
DTC P2135 TP SENSOR
2007 Pathfinder
DTC P2135 TP SENSOR
PFP:16119
Component Description
UBS00KHF
Electric throttle control actuator consists of throttle control motor,
throttle position sensor, etc. The throttle position sensor responds to
the throttle valve movement.
The throttle position sensor has the two sensors. These sensors are
a kind of potentiometers which transform the throttle valve position
into output voltage, and emit the voltage signal to the ECM. In addi-
tion, these sensors detect the opening and closing speed of the
throttle valve and feed the voltage signals to the ECM. The ECM
judges the current opening angle of the throttle valve from these sig-
nals and the ECM controls the throttle control motor to make the
throttle valve opening angle properly in response to driving condi-
tion.
CONSULT-II Reference Value in Data Monitor Mode
UBS00KHG
Specification data are reference values.
*: Throttle position sensor 2 signal is converted by ECM internally. Thus, it differs from ECM terminal voltage signal.
On Board Diagnosis Logic
UBS00KHH
This self-diagnosis has the one trip detection logic.
FAIL-SAFE MODE
When the malfunction is detected, the ECM enters fail-safe mode and the MIL lights up.
PBIB0145E
MONITOR ITEM
CONDITION
SPECIFICATION
THRTL SEN 1
THRTL SEN 2*
●
Ignition switch: ON
(Engine stopped)
●
Shift lever: D
Accelerator pedal: Fully released
More than 0.36V
Accelerator pedal: Fully depressed
Less than 4.75V
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P2135
2135
Throttle position sensor
circuit range/perfor-
mance
Rationally incorrect voltage is sent to ECM
compared with the signals from TP sensor 1
and TP sensor 2.
●
Harness or connector
(The TP sensor 1 and 2 circuit is open or
shorted.)
(The APP sensor 2 circuit is shorted).
●
Electric throttle control actuator
(TP sensor 1 and 2)
●
Accelerator pedal position sensor
(APP sensor 2)
Engine operation condition in fail-safe mode
The ECM controls the electric throttle control actuator in regulating the throttle opening in order for the idle position to be within +10
degrees.
The ECM regulates the opening speed of the throttle valve to be slower than the normal condition.
So, the acceleration will be poor.
DTC P2135 TP SENSOR
EC-593
C
D
E
F
G
H
I
J
K
L
M
A
EC
2007 Pathfinder
DTC Confirmation Procedure
UBS00KHI
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10V at idle.
WITH CONSULT-II
1.
Turn ignition switch ON.
2.
Select “DATA MONITOR” mode with CONSULT-II.
3.
Start engine and let it idle for 1 second.
4.
If DTC is detected, go to
EC-595, "Diagnostic Procedure"
WITH GST
Follow the procedure “WITH CONSULT-II” above.
SEF058Y
EC-594
DTC P2135 TP SENSOR
2007 Pathfinder
Wiring Diagram
UBS00KHJ
BBWA1746E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст