Nissan 370Z (2018 year). Instruction — part 18
SAA2540
9. The system announces, “Dial or
Change Number?”
10. Speak “Dial”.
11. The system makes a call to 800-662-
6200.
Note:
. You can also speak “800-662-6200”
(10 continuous digits) or “662-6200” (7
continuous digits), if the area code is
not necessary. However, the 3-3-4
digit grouping is recommended for
improved recognition. (See “How to
say numbers” (P.4-89).)
. You can only say a phone number
using the 3-3-4 grouping, 7 digits, and
10 digits using this command. Please
use the “International Call” command
for all other formats.
. If you say “Change Number” during
phone number entry, the system will
automatically request that you repeat
the number using the 3-3-4 format. In
this case please say the area code first
and then follow the prompts.
. Do not add a “1” in front of the area
code when speaking phone numbers.
. If the system does not recognize your
command, please try repeating the
command using a natural voice.
Speaking too slow or too loudly may
further decrease recognition perfor-
mance.
SAA2167
Example 2 - Placing an international call
to the phone number 011-81-111-222-
3333:
1. Push the TALK
switch located on
the steering wheel. You will hear a
prompt.
2. Speak “Phone”.
Center display, heater, air conditioner, audio, phone and voice recognition systems
4-109
4-110
Center display, heater, air conditioner, audio, phone and voice recognition systems
JVH0481X
3. Speak “International Call”.
SAA2541
4. Speak “011811112223333”.
SAA2542
5. Speak “Dial”.
6. System makes a call to 011-81-111-222-
3333.
Note:
Any digit input format is available in the
International Number input process.
NISSAN VOICE RECOGNITION AL-
TERNATE COMMAND MODE
The following section is applicable when
Alternate Command Mode is activated.
When Alternate Command Mode is acti-
vated, an expanded list of commands can
be used after pressing the TALK
switch. In this mode, available commands
are not fully shown on the display or
prompted. Review the expanded com-
mand list when this mode is active. See
examples of Alternate Command Mode
screens.
Please note that in this mode the recog-
nition success rate may be affected as
the number of available commands and
ways of speaking each command are
increased. To improve the recognition
success rate, try using the Speaker Adap-
tation Function available in that mode.
(See “Speaker adaptation function (for
Alternate Command Mode)” (P.4-121).)
Otherwise it is recommended that Alter-
nate Command Mode be turned OFF and
Standard Mode be used for the best
recognition performance.
SAA2529
Activating Alternate Command
Mode
When the Standard Mode is active, per-
form the following steps to switch to the
Alternate Command Mode.
1. Push the SETTING button on the
instrument panel.
2. Highlight the “Others” key.
3. Highlight the “Voice Recognition” key.
SAA2543
4. Highlight the “Alternate Command
Mode” key.
5. The confirmation message is dis-
played on the screen. Push the “OK”
key to activate the Alternate Com-
mand Mode.
Displaying command list
If you are controlling the system by voice
commands for the first time or do not
know the appropriate voice command,
perform the following procedure for dis-
playing the voice command list (available
only in Alternate Command Mode).
Center display, heater, air conditioner, audio, phone and voice recognition systems
4-111
4-112
Center display, heater, air conditioner, audio, phone and voice recognition systems
SAA2544
1. Push the INFO button on the instru-
ment panel.
2. Select the “Others” key.
3. Select the “Voice Recognition” key.
4. Select the “Command List” key.
SAA2545
5. Select a category from the list.
JVH0483X
6. Select an item.
7. If necessary, scroll the screen using
the multi-function controller to view
the entire list.
8. Push the BACK button to return to the
previous screen.
Commands List
Phone Commands:
Command
Action
Dial Number
Makes a call to a spoken phone number.
Quick Dial
Makes a call to a contact that is stored in the Quick Dial.
Phonebook
Makes a call to a contact that is stored in the mobile phone.
Call History
Incoming Calls
Makes a call to the incoming call number.
Outgoing Calls
Makes a call to the dialed number.
Missed Calls
Makes a call to the Missed calls number.
International Call
Makes an international call by allowing more than 10 digits to be spoken.
Call <name>
Makes a call to a contact that is stored in either Quick Dial or Phonebook. Please say “Call” followed
by a stored name.
Change Number
Corrects the recognized phone number (available during phone number entry).
Center display, heater, air conditioner, audio, phone and voice recognition systems
4-113
4-114
Center display, heater, air conditioner, audio, phone and voice recognition systems
Navigation Commands:
Command
Action
Destination Home
Sets a route to your home that is stored in the Address Book.
Address
Searches for a location by the street address specified, and sets a route to the location.
Places
Sets a route to a facility near the current vehicle location.
Address Book
Searches for stored information in the Address Book.
Previous Destinations
Sets a route to a previous destination.
Previous Start Point
Sets a route to a previous starting point.
Delete Destination
Deletes a destination.
Information Commands:
Command
Action
Fuel Economy
Displays fuel economy information.
Maintenance
Displays maintenance information.
Where am I?
Displays your current location.
Traffic Information
Turns the traffic information system ON and OFF.
Weather Information
Displays weather information.
Weather Map
Displays a weather map.
Center display, heater, air conditioner, audio, phone and voice recognition systems
4-115
4-116
Center display, heater, air conditioner, audio, phone and voice recognition systems
Audio Commands:
Command
Action
CD
Starts to play a CD.
FM
Turns to the FM band, selecting the station last played.
AM
Turns to the AM band, selecting the station last played.
XM
Turns to the SiriusXM Satellite Radio band, selecting the channel last played.
USB
Turns on the USB memory.
Bluetooth Audio
Turns on the Bluetooth® audio player.
AUX
Turns on the AUX.
Help Commands:
Command
Action
Command List
Navigation Commands Displays the navigation command list.
Phone Commands
Displays the phone command list.
Audio Commands
Displays the audio command list.
Information Com-
mands
Displays the information command list.
Help Commands
Displays the help command list.
User Guide
Displays the User Guide.
Speaker Adaptation
The system can memorize the voices of up to three persons.
Center display, heater, air conditioner, audio, phone and voice recognition systems
4-117
4-118
Center display, heater, air conditioner, audio, phone and voice recognition systems
General Commands:
Command
Action
Go back
Corrects the last recognition result to return to the previous screen
Exit
Cancels Voice Recognition
SAA2547
Displaying user guide
You can confirm how to use voice com-
mands by accessing a simplified User
Guide, which contains basic instructions
and tutorials for several voice commands.
1. Push the INFO button on the instru-
ment panel.
2. Select the “Others” key using the
multifunction controller and push the
ENTER button.
3. Highlight the “Voice Recognition” key
using the multi-function controller
and push the ENTER button.
4. Highlight the “User Guide” key using
the multi-function controller and push
the ENTER button.
5. Highlight an item using the multi-
function controller and push the
ENTER button.
Available items:
. Getting Started
Describe the basics of how to operate
the NISSAN Voice Recognition system.
. Let’s Practice
Mode that allows practicing by follow-
ing the instructions of the system
voice.
. Using the Address Book
Refer to Navigation System Owner’s
Manual.
. Finding a Street Address (if so
equipped)
Refer to Navigation System Owner’s
Manual.
. Placing Calls
Tutorial for making a phone call by
voice command operation.
. Help on Speaking
Displays useful tips for how to cor-
rectly speak commands in order for
them to be properly recognized by the
system.
. Voice Recognition Settings
Describes the available voice recogni-
tion settings.
. Adapting the System to Your Voice
Tutorial adapting the system to your
voice.
USING THE SYSTEM
Initialization
When the ignition switch is pushed to the
ON position, NISSAN Voice Recognition is
initialized, which may take up to one
minute. When completed, the system is
ready to accept voice commands. If the
TALK
switch is pushed before the
initialization completes the display will
show the message: “System not ready.”
or a beep sounds.
Before starting
To get the best performance from NISSAN
Voice Recognition, observe the following.
. Keep the interior of the vehicle as
quiet as possible. Close the windows
to eliminate the surrounding noises
(traffic noises, vibration sounds, etc.),
which may prevent the system from
recognizing the voice commands cor-
rectly.
. When the air conditioner is in the
AUTO mode, the fan speed decreases
automatically for easy recognition.
. Wait until a tone sounds before speak-
ing a command.
Center display, heater, air conditioner, audio, phone and voice recognition systems
4-119
4-120
Center display, heater, air conditioner, audio, phone and voice recognition systems
. Speak in a natural voice without
pausing between words.
SAA2167
Giving voice command
1. Push and release the TALK
switch
located on the steering wheel.
2. A list of commands appears on the
screen, and the system announces,
“Please say a command”.
3. After the tone sounds and the icon on
the screen changes from
to
,
speak a command.
Operating tips:
. Voice commands cannot be accepted
when the icon is
.
. The list displayed can be scrolled by
tilting the menu control switch on the
steering wheel.
. If the command is not recognized, the
system announces, “Please say again”.
Repeat the command in a clear voice.
. Push the BACK button once to return
to the previous screen.
. If you want to cancel the command,
push and hold the TALK
switch for
1 second. The message “Voice can-
celed” will be announced.
Voice Prompt Interrupt:
To skip the voice guidance function and
give the command immediately, push the
TALK
switch to interrupt the system.
Remember to speak after the tone.
How to speak numbers:
NISSAN Voice Recognition requires a
certain way to speak numbers when
giving voice commands. Refer to the
following examples.
General rule
Only single digits 0 (zero) to 9 can be
used. (For example, if you would like to
say 500, “five zero zero” can be used, but
“five hundred” cannot.
Phone numbers
Speak phone numbers according to the
following examples:
. 1-800-662-6200
— “Dial one eight zero zero six six two
six two zero zero.”
Note 1: For the best voice recognition
phone dialing results, say phone numbers
as single digits.
Note 2: You cannot say 555-6000 as “five
five five six thousands”.
Note 3: When speaking a house number,
speak the number “0” as “zero”. If the
letter “o (oh)” is included in the house
number, it will not be recognized as the
number “0 (zero)” even if you speak “oh”
instead of “zero”. Please speak “zero” for
the number “0 (zero)”, “oh” for the letter “o
(oh)”.
Send digits using dial tone:
. Push the TALK
switch during a
phone call.
. The menu will be launched and you
will be provided with the following
guidance: "Please say the digits to
dial".
. After guidance, say the digits of the
number you want to send. After this,
the digits that have been recognized
will be read out.
. If you push the ENTER button on the
steering wheel or on the multi-func-
tion controller, the selected digits will
be sent.
SAA2549
Speaker adaptation function (for
Alternate Command Mode)
The voice recognition system has a func-
tion to learn the user’s voice for better
voice recognition performance. The sys-
tem can memorize the voices of up to
three persons.
Having the system learn the user’s
voice:
1. Push the SETTING button on the
instrument panel and select the
“Others” key.
2. Select the “Voice Recognition” key.
3. Select the “Speaker Adaptation” key.
Center display, heater, air conditioner, audio, phone and voice recognition systems
4-121
4-122
Center display, heater, air conditioner, audio, phone and voice recognition systems
SAA2550
4. Select the user whose voice is mem-
orized by the system.
5. Select the “Start Speaker Adaptation
Learning” key.
SAA2551
6. Select a category to be learned by the
system from the following list.
.
Phone Commands
.
Navigation Commands
.
Information Commands
.
Audio Commands
.
Help Commands
The voice commands in the cate-
gory are displayed.
7. Select a voice command and then
push the ENTER button.
The voice recognition system starts.
SAA2552
8. The system requests that you repeat a
command after a tone.
9. After the tone sounds and the icon on
the screen changes from
to
,
speak the command that the system
requested.
10. When the system has recognized the
voice command, the voice of the user
is learned.
Push the
switch or BACK button to
return to the previous screen.
If the system has learned the command
correctly, the voice command status on
the right side of the command turns from
“None” to “Stored”.
SAA2553
Speaker Adaptation function settings:
Edit User Name
Edit the user name using the keypad
displayed on the screen.
Delete Voice Data
Resets the user’s voice that the voice
recognition system has learned.
Continuous Learning
When this item is turned to ON, you can
have the system learn the voice com-
mands in succession, without selecting
commands one by one.
Minimize voice feedback (for Alter-
nate Command Mode)
To minimize the voice feedback from the
system, perform the following steps.
1. Push the SETTING button on the
instrument panel.
2. Select the “Others” key.
3. Select the “Voice Recognition” key.
4. Select the “Minimize Voice Feedback”
key.
5. The setting is turned to ON and the
voice guidance will now be reduced
when using the Voice Recognition
system.
Center display, heater, air conditioner, audio, phone and voice recognition systems
4-123
4-124
Center display, heater, air conditioner, audio, phone and voice recognition systems
TROUBLESHOOTING GUIDE
The system should respond correctly to all voice commands without difficulty. If problems are encountered, follow the solutions
given in this guide for the appropriate error.
Where the solutions are listed by number, try each solution in turn, starting with number one, until the problem is resolved.
Symptom/error message
Solution
The system fails to interpret the command
correctly.
1. Ensure that the command format is valid, see “Command List” (P.4-105).
2. Speak clearly without pausing between words and at a level appropriate to the ambient noise
level.
3. Ensure that the ambient noise level is not excessive, for example, windows open or defrost on.
NOTE:
If it is too noisy to use the phone, it is likely that voice commands will not be recognized.
4. If optional words of the command have been omitted, then the command should be tried with
these in place.
The system consistently selects the wrong
voicetag in the phonebook.
1. Ensure that the voicetag requested matches what was originally stored. (See “Bluetooth® hands-
free phone system (models with navigation system)” (P.4-76).)
2. Replace one of the voicetags being confused with a different voicetag.
The system cannot be operated.
1. Make sure that the soft top (for Roadster models) is usable. If the soft top is not working, it is
recommended to contact a NISSAN dealer.
2. Close the soft top (for Roadster models).
3. Open and close the soft top (for Roadster models) before operating the system.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст