Nissan Titan A60. Manual — part 662
INTERIOR LIGHTING SYSTEM SYMPTOMS
INL-69
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
SYMPTOM DIAGNOSIS
INTERIOR LIGHTING SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000006164485
CAUTION:
Perform the self-diagnosis with CONSULT-III before the symptom diagnosis. Perform the trouble diag-
nosis if any DTC is detected.
Symptom
Possible cause
Inspection item
All of the following lamps do not turn ON
• Room lamp (if equipped)
• Front room/map lamp assembly (if equipped)
• Personal lamp 2nd row (if equipped)
• Vanity lamps (if equipped)
• Front step lamps (if equipped)
• Puddle lamps (if equipped)
• Foot lamps (if equipped)
• Harness between BCM and each
interior room lamp
• BCM
Battery saver output/power supply
circuit.
Refer to
.
Some or all of the following interior room lamps do not
turn ON/OFF
• Room lamp (if equipped)
• Puddle lamps (if equipped)
• Front room/map lamp assembly (if equipped)
• Personal lamp 2nd row (if equipped)
• Harness between BCM and each
door switch
• Harness between BCM and each
interior room lamp
• BCM
(king cab) or
29, "CREW CAB : Diagnosis Proce-
dure"
(crew cab).
Interior room lamp control circuit.
Refer to
Some or all of the following lamps do not turn ON/OFF
• Front step lamps
• Foot lamps (if equipped)
• Harness between BCM and step
lamps and foot lamps
• BCM
Step lamp circuit.
Refer to
Cargo lamp and tailgate cargo lamps (if equipped) do
not turn ON/OFF
• Harness between BCM and cargo
lamp relay
• Harness between cargo lamp relay
and cargo lamps
• BCM
• Cargo lamp relay
Cargo lamp control circuit.
Refer to
Interior room lamp timer does not activate.
(It turns ON/ OFF when the door opens/closes.)
—
Check the interior room lamp setting.
Refer to
SULT-III Function (BCM - INT
LAMP)"
Interior room lamp battery saver does not activate.
—
Check the interior room lamp battery
saver setting.
Refer to
CONSULT-III Function (BCM - BAT-
TERY SAVER)"
.
INL-70
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000006164486
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution for Work
INFOID:0000000006698790
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components.
- Water soluble dirt: Dip a soft cloth into lukewarm water, and wring the water out of the cloth to wipe the dirty
area.
Then rub with a soft and dry cloth.
- Oily dirt: Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%), and wipe
the dirty area.
Then dip a cloth into fresh water, and wring the water out of the cloth to wipe the detergent off. Then rub with
a soft and dry cloth.
• Do not use organic solvent such as thinner, benzene, alcohol, or gasoline.
• For genuine leather seats, use a genuine leather seat cleaner.
PREPARATION
INL-71
< PREPARATION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000006698791
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
—
( J-46534 )
Trim tool set
For removing trim
AWJIA0483ZZ
INL-72
< REMOVAL AND INSTALLATION >
INTERIOR ROOM LAMP
REMOVAL AND INSTALLATION
INTERIOR ROOM LAMP
Removal and Installation
INFOID:0000000006164488
FRONT ROOM/MAP LAMP (If Equipped)
Removal
The front room/map lamp is replaced as part of the front roof console. Refer to
INT-21, "Removal and Installa-
.
Installation
Installation is in the reverse order of removal.
Bulb or Lens Replacement
1. Using a suitable tool (A), remove front room/map lamp lens (1).
: Pawl
CAUTION:
Wrap a cloth around suitable tool (A) to protect the housing
and lens (1).
2. Release one side of the bulb (2) from the tab, then pull straight
downward to remove.
ROOM LAMP (If Equipped)
Removal
Front room/map lamp
bulb
: 12V - 6W
ALLIA0319ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст