Nissan Titan A60. Manual — part 296
FRONT DRIVE SHAFT
DLN-123
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TX15B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
FRONT DRIVE SHAFT
Disassembly and Assembly
INFOID:0000000006179510
DISASSEMBLY
1. Remove the front bearing using Tools.
2. Remove the rear bearing using Tools.
INSPECTION AFTER DISASSEMBLY
Front Drive Shaft
Check the items below. If necessary, replace them with new ones.
• Damage, peeling, dent, uneven wear and bending of the shaft.
• Excessive wear, damage and peeling of the gear.
Bearing
Check the bearing for damage and rough rotation. If necessary,
replace the bearing with a new one.
ASSEMBLY
Tool number
A: ST35300000 ( — )
B: ST30021000 (J-22912-01)
SDIA2106E
Tool number
A: ST33710000 ( — )
B: ST30021000 (J-22912-01)
PDIA0153E
PDIA0154E
MTF0041D
DLN-124
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TX15B]
FRONT DRIVE SHAFT
1. Install the rear bearing using Tools.
2. Install the front bearing using Tools.
Tool number
A: KV38100500 ( — )
B: ST30901000 (J-26010-01)
PDIA0155E
Tool number
A: KV38100500 ( — )
B: ST30901000 (J-26010-01)
PDIA0156E
SHIFT CONTROL
DLN-125
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TX15B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
SHIFT CONTROL
Disassembly and Assembly
INFOID:0000000006179511
DISASSEMBLY
1. Remove the snap ring.
2. Remove the retaining pin.
3. Remove the drum cam from the control shift rod.
4. Remove the retaining pin from the L-H shift rod.
5. Remove the 2-4 shift bracket.
6. Remove the retaining ring from the 2-4 shift fork using suitable
tool.
7. Remove the fork guide collar and 2-4 shift fork spring from the 2-
4 shift fork.
INSPECTION AFTER DISASSEMBLY
Shift Fork
• Measure the clearance between the shift fork and sleeve. If it is out
of specification, replace it with a new one.
Shift Rod and Fork Components
PDIA0122E
PDIA0125E
WDIA0226E
Standard value
2-4
: Less than 0.46 mm (0.018 in)
L-H
: Less than 0.46 mm (0.018 in)
PDIA0134E
DLN-126
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TX15B]
SHIFT CONTROL
• Check the working face of the shift rod and fork for wear, partial
wear, abrasion, bending and other abnormality. If any is found,
replace with a new one.
ASSEMBLY
1. Install clevis pin and shift collar to L-H shift fork after assembling them.
CAUTION:
Use caution when installing L-H shift fork, clevis pin or shift collar.
2. Install clevis pin and shift collar to 2-4 shift bracket after assembling them.
CAUTION:
Use caution when installing 2-4 shift bracket.
3. Install guide fork collar and 2-4 shift fork spring to the 2-4 shift
fork, and then secure it with the new retaining ring.
CAUTION:
• Do not reuse retaining ring.
• Be careful with orientation.
4. Install the 2-4shift bracket to the L-H shift rod.
5. Install the new retaining pin evenly to the L-H shift rod.
CAUTION:
Do not reuse retaining pin.
6. Install the drum cam to the control shift rod, and then secure it
with the new retaining pin.
CAUTION:
Do not reuse retaining pin.
7. Install the new snap ring to the control shift rod.
CAUTION:
Do not reuse snap ring.
PDIA0135E
SDIA3391E
PDIA0125E
PDIA0122E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст